587,108 active members*
3,372 visitors online*
Register for free
Login
IndustryArena Forum > MetalWorking Machines > Milltronics > help programming radius cent V lathe

Thread: help programming radius cent V lathe

Results 1 to 5 of 5
  1. 05-21-2009, 03:18 PM #1
    Joe Miranda
    Joe Miranda is offline Registered
    Join Date
    Dec 2005
    Posts
    134

    help programming radius cent V lathe

    I need help programming some parts with radii's on a lathe with a cent v controller. Can someone help me out?
    Thanks
    Joe
    Attached Files Attached Files
    Reply With Quote Reply With Quote
  2. 05-23-2009, 12:44 AM #2
    LYN BYRD
    LYN BYRD is offline Registered
    Join Date
    Jul 2004
    Posts
    97
    ARE YOU PROGRAMMING WITH CONVERSATIONAL?
    Reply With Quote Reply With Quote
  3. 05-23-2009, 04:54 AM #3
    Joe Miranda
    Joe Miranda is offline Registered
    Join Date
    Dec 2005
    Posts
    134
    Yes conversational.
    Reply With Quote Reply With Quote
  4. 05-23-2009, 02:53 PM #4
    LYN BYRD
    LYN BYRD is offline Registered
    Join Date
    Jul 2004
    Posts
    97

    PROGRAM

    JOE,
    EVENT #1-PROGRAM START
    EVENT #2-MISC-CALL WORK COORD#1
    EVENT #3-TOOL CHANGE OR CALL
    EVENT #4-POS-X4.500 Z0.000 (RAPID)
    EVENT #5-POS-X0.000 (FEED) FACING
    EVENT #6-POS-X4.500 Z.125 (RAPID)
    EVENT #7-TURN RUFF (ENTER VALUES FOR FINISH,RUFF AMOUNT & START POINT, & ETC)
    EVENT #8-LINE X1.470 Z.125
    EVENT #9-LINE Z0.000
    EVENT#10-ARC CCW XCENTER-0.000 ZCENTER-2.250 XEND-4.400 ZEND-(-)1.250
    EVENT#11-LINE Z-2.125
    EVENT#12-END
    HOPE THIS HELPS
    LYN
    Reply With Quote Reply With Quote
  5. 05-24-2009, 03:40 AM #5
    Joe Miranda
    Joe Miranda is offline Registered
    Join Date
    Dec 2005
    Posts
    134
    Thanks Lyn! I will give this a try.
    Joe
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. programming a radius
    By honda27 in forum G-Code Programing
    Replies: 3
    Last Post: 10-31-2008, 02:25 PM
  2. From Radius to Diameter Programming
    By metx in forum Fanuc
    Replies: 7
    Last Post: 04-10-2008, 07:04 PM
  3. Programming a radius
    By fukeneh in forum G-Code Programing
    Replies: 8
    Last Post: 07-14-2007, 03:35 AM
  4. programming radius/ help needed
    By integrexe410 in forum Mazak, Mitsubishi, Mazatrol
    Replies: 6
    Last Post: 12-11-2006, 07:14 PM
  5. Programming lathe with radius numbers
    By mudwhump in forum BobCad-Cam
    Replies: 1
    Last Post: 06-07-2004, 01:14 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules