586,911 active members*
3,846 visitors online*
Register for free
Login
IndustryArena Forum > CNC Electronics > CNC Machine Related Electronics > makino ec 3025 battery drop alarm
Results 1 to 10 of 10
  1. #1
    Join Date
    Jul 2009
    Posts
    1

    makino ec 3025 battery drop alarm

    hi this is my first time to ever post and hope im doing it right i have a makino edm ec 3025 approx 1988
    i havent used it in a month and i turn it on and get a alarm code 0020 battery drop the book says it might be in the power supply but i cant see a battery i tried makino but they wouldnt help me unless i gave them $2500. for phone support and i dont think the machine is worth much more then that.
    dose anyone know where the battery might be located or what board i need to have repared

  2. #2
    Join Date
    Dec 2005
    Posts
    12
    makino edm ec 3025
    i am helping u
    iam sending photos shortly
    u finding battries

  3. #3
    Join Date
    Dec 2005
    Posts
    12
    i have same makino ec 3025 machine in running codition

  4. #4
    Join Date
    Feb 2010
    Posts
    0

    Makino EC 3025

    Hi, i have a makino ec 3025 1986 and i'm having trouble figuring out how to send my program to the machine using mastercam. Any help would be appreciated, thanks.

  5. #5
    Join Date
    Dec 2005
    Posts
    12
    use winpcin software from simens

  6. #6
    Join Date
    Feb 2010
    Posts
    0
    thanks for the reply. I'm guessing mastercam can't be used to send the program? what about hyperlink? if wincpin is the only way to go ill get it. I've went through the books for this machine but i'm unable to find what communication ports to use in order to communicate with the machine. (baud rate, stop bit, etc.)

  7. #7
    Join Date
    Dec 2005
    Posts
    12
    Settings for machine:
    excute extrenal
    readin
    settings for winpcin:
    baud rate=4800, stop bit=1, PARITY=EVEN, DATA=7

  8. #8
    Join Date
    Dec 2005
    Posts
    12
    give your email id
    i am sending winpcin softwrae&rs232 settings

  9. #9
    Join Date
    Dec 2005
    Posts
    12
    your problem is soved or not
    other vise contact me

  10. #10
    Join Date
    Aug 2008
    Posts
    8

    BATTERY LOCATION

    EC 3025...open cabinet..front door...on left will be a series of cards. 3 of these cards will have three flat batteries on the front edge on each card(they are connected together and each battery is about the size of a quarter).You can replace batteries while power is on and not loose parameters....(be carefull...
    not recommended). Otherwise, power off..change batteries...write down parameter 3011and 4011. Load parameters from tape and after installation, input 3011 and 4011 numbers
    or square up wire with block...this will replace 3011 and 4011 settings.
    Toppik

Similar Threads

  1. alarm 124 low battery
    By metaler in forum Haas Mills
    Replies: 73
    Last Post: 01-22-2018, 09:35 PM
  2. Makino EC 3025 Cables
    By Paul Deady in forum EDM Discussion General Topics
    Replies: 0
    Last Post: 01-28-2009, 02:11 AM
  3. Replies: 2
    Last Post: 07-17-2007, 04:19 PM
  4. compressor causes voltage drop and alarm
    By 1ctoolfool in forum Haas Mills
    Replies: 6
    Last Post: 06-01-2007, 09:57 PM
  5. O-MD servos jumping battery alarm
    By SpringKing in forum Fanuc
    Replies: 2
    Last Post: 08-25-2006, 10:55 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •