[sisbir]

Hello All,

I have a Victor V center 4 10MA and system parameters and PC-NC parameters for this machine are needed.

The situation with the machine is:
Our guys tried to clean the electronic parts and accidentally removed the battery in the system !!

I guess this powered the backup memory which is erased now. The machine locked itself up. There is a CNC service guy working on the machine now. He resetted the machine. Now we need the system parameters, to start the machine.

Urgent help is needed. Thanks for your help in advance.

[stevo1]

Do you have a hard copy of the original parameters? The MTB usually puts a hard copy in the power cabinet however these usually disappear over time. If not the 3 options you have are 1.to try and contact the MTB if they are still around they should have a file of all the original parameters. 2.Find someone with the same make/model of your machine and control and get the parameters from them. 3.Step through the parameters 1 at a time using your manual and set each one accordingly. The third is a major PITA.

I can never stress enough that when getting a new or used machine or starting at a new company the first order of business when the machine is first powered on is to backup everything in the control.

In the event that you get parameters you have to enter your option parameters in first through the IPL mode. This will then get you to the CNC were you can set up your communication parameters and then reload all the parameters. Your counters, timers, keeprelys, and data will have to be loaded by hand.

Stevo

[sisbir]

Hi Guys,

Mr. Tony Gannon provided the missing parameters. I thank him for his help. Contact info is below, in case somebody else needs help.

Tony Gannon
Victor Europe Ltd U.K.
Tel: +44 (0) 1706 648485
Fax : +44 (0) 1706 648485
www.victoreurope.com

Best Regards,

[abrars]

Hello sir

I have a Victor V center 4 10MA and system parameters and PC-NC parameters for this machine are needed.
[quote]
The situation with the machine is:
Our guys tried to clean the electronic parts and accidentally removed the battery in the system !!

I guess this powered the backup memory which is erased now. The machine locked itself up. There is a CNC service guy working on the machine now. He resetted the machine. Now we need the system parameters, to start the machine.

Urgent help is needed. Thanks for your help in advance.


email:[email protected]

[abrars]

--------------------------------------------------------------------------------

Hello sir

I have a Victor V center 4 10MA and system parameters and PC-NC parameters for this machine are needed.

The situation with the machine is:
Our guys tried to clean the electronic parts and accidentally removed the battery in the system !!

I guess this powered the backup memory which is erased now. The machine locked itself up. There is a CNC service guy working on the machine now. He resetted the machine. Now we need the system parameters, to start the machine.

Urgent help is needed. Thanks for your help in advance.

[abrars]

--------------------------------------------------------------------------------

Hello sir

I have a Victor V center 4 10MA and system parameters and PC-NC parameters for this machine are needed.

The situation with the machine is:
Our guys tried to clean the electronic parts and accidentally removed the battery in the system !!

I guess this powered the backup memory which is erased now. The machine locked itself up. There is a CNC service guy working on the machine now. He resetted the machine. Now we need the system parameters, to start the machine.

Urgent help is needed. Thanks for your help in advance.
email:[email protected]

[vladimir1409]

abrars PM sent

[CNC_Chicago]

abrars PM sent

Can i get the PC NC parameters as well for the Victor Vcenter-4
I need timer keep relay and counters atc program!
thanking you in advance.
you can email me at [email protected]

[abrars]

Do you have a hard copy of the original parameters? The MTB usually puts a hard copy in the power cabinet however these usually disappear over time. If not the 3 options you have are 1.to try and contact the MTB if they are still around they should have a file of all the original parameters. 2.Find someone with the same make/model of your machine and control and get the parameters from them. 3.Step through the parameters 1 at a time using your manual and set each one accordingly. The third is a major PITA.

I can never stress enough that when getting a new or used machine or starting at a new company the first order of business when the machine is first powered on is to backup everything in the control.

In the event that you get parameters you have to enter your option parameters in first through the IPL mode. This will then get you to the CNC were you can set up your communication parameters and then reload all the parameters. Your counters, timers, keeprelys, and data will have to be loaded by hand.

Stevo

can you me help me send parameter of
v center 4 ma 10 nk 1286
i will be thanfull

[abrars]

con any one help me to send victor v center 4 ma 10
parameter NK 1286

[stevo1]

Do you mean load them into the machine?

Stevo

[sunil8667]

Do you mean load them into the machine?

Stevo

While trying to do the tool change the error message light is on so now i can run machine in manual mode but not in auto mode . needs procedure to recover the ATC .I mea to say that when i press NC/PC and press ladder .the ladder is not displayed .

[vladimir1409]

sunil8667

I sent you the manuals I have(on your email) for the victor there is a procedure to reference the ATC you will find in the manual, it should solve the problem with the error light.

if you don't have the (counter, keep relay, timer etc) parameters you wont be able to use the tool charger

[gbowne1]

Yeah I remember a friend of mine had one of these Victor's in his shop. It had missing parameters. Parameters were entered and the ATC still didnt work. I dont remeber if he sorted out the timers, relays, etc.

[alexfanuc]

Yeah I remember a friend of mine had one of these Victor's in his shop. It had missing parameters. Parameters were entered and the ATC still didnt work. I dont remeber if he sorted out the timers, relays, etc.

The ATC works when you have a macro program (9000 program)

[vd51]

hello vladimir

i have same problem with vcenter-4 ATC,please can you email me manuals that you have,i haven't any manuals,erroe led is on and atc don't work,thanks
and best regards.

[agering]

Hi vd51,
What parameters options you interest, please tell private message to me or your PM.

[jameel123]

sunil8667

I sent you the manuals I have(on your email) for the victor there is a procedure to reference the ATC you will find in the manual, it should solve the problem with the error light.

if you don't have the (counter, keep relay, timer etc) parameters you wont be able to use the tool charger

My Name is Jameel we had purchase Victor V Center 4 VMC six months before and we started the machine unfortunately we lost backup file from the machine how ever we loaded the backup file but techinical people are asking(counter, keep relay, timer ATC Programming) if you can help me out so that we can start our machine.

[zavateandu]

My Name is Jameel we had purchase Victor V Center 4 VMC six months before and we started the machine unfortunately we lost backup file from the machine how ever we loaded the backup file but techinical people are asking(counter, keep relay, timer ATC Programming) if you can help me out so that we can start our machine.

what is the serial number of machine?

[sunil8667]

Need Help
I have a Victor V4 vmc with fanuc 10MD control with red cap motor . The serial number is vanished .I do not have manuals for this machine .I could install the basic machine i.e all axes movement .spindle rotaion etc .now stuck up with atc .gave mo6 command the orientaon took place then te pot came down .then the error lamp light glow .and it is not going .also one more problem the ladder is not dislayed ,may be locked .

need help
email [email protected]