[klabacita]

Hi people.

I have 2 machines:
1; Morbidelli Author 504k
Control Tria 7500
2; Morbidelli Author 504
Control Tria 7500

Normally we load the programs via floppies, we want to use the serial port of the controller, but we don't have the manual, I have googling but I have not found the info.

Some could help me with this info? I will build the cable what is the configuration? Someone have the manual for this machines?
Last thing, how to setup the connection?(Parity, Stop Bit, etc, etc.)

Thanks all for your time, hope someone could show me some light, I will apprecited, thanks again for your time!!!

[beeonline]

Hi people.

I have 2 machines:
1; Morbidelli Author 504k
Control Tria 7500
2; Morbidelli Author 504
Control Tria 7500

Normally we load the programs via floppies, we want to use the serial port of the controller, but we don't have the manual, I have googling but I have not found the info.

Some could help me with this info? I will build the cable what is the configuration? Someone have the manual for this machines?
Last thing, how to setup the connection?(Parity, Stop Bit, etc, etc.)

Thanks all for your time, hope someone could show me some light, I will apprecited, thanks again for your time!!!

Do you still need information?
I have Morbideli A502 & U550 I have also been using only floppies but I plan to use serial cable and Kermit. I have information available but not the experience at this stage. I am happy to supply the documentation I have.

[CNCRouterMan]

Do you still need information?
I have Morbideli A502 & U550 I have also been using only floppies but I plan to use serial cable and Kermit. I have information available but not the experience at this stage. I am happy to supply the documentation I have.

Try this connection. See Attached

[morbi]

Hello Morbidelli 504 Guys,
I've owned a '94 504 for a while now and just had to replace the Inverter with a new one made by Fuji.The problem I'm having is that we wired in the Inverter tonight and the Programm stops with the Spindle running with the Z Axis in upper position.I assume there is a signal not being sent to the controls, that the correct RPM has been reached.We let the spindle run at roughly 5000 RPM.Could this have an Impact on the Progamm being interrupted? I unfortunatelly haven't seen the spindle run untill today on this machine, so I have no referance.Would I possably have to reduce the RPM that the Spindle was set at to make this work? I would really apreciate any respond to the Problem I am experiencing. Thank you!

[Ciberfacu]

Have resolved the inverter problem ?

[artan]

I have Morbidelli author 504 CNC machine I want to use my pc to send files to the CNC machine.
Does anyone know how can I do that?
what dnc software is compatibil with author 504.
I use RS232.

[berketi5]

Hello to everyone, i have a cnc morbidelli , Author 455, i have an error massage: "Plc80:tool out of possition" when the router is working, it's stops and i have this error. some times the analoge output from plc to inverter(must be 10volts) is 3.48volts and the machine stops. I check the limit swich, and is ok.
I don't know what else i have to check. The orizontal router is working.
thank you very much.

[pmdwood]

I have a morbidelli 504 with a Tria 7500 controller battery has gone need info on getting it going again?
Thanks

[pmdwood]

I have a morbidelli A504 with a Tria 7500 controller and side tool changer. Battery has gone dead, need info on getting it going again or where I can get help?
Thanks.

[unleash_jad]

I have the same problem now, have you resolved it? PLEASE HELP! It says error "PLC STOPPED"

[pmdwood]

hi all,
I got sorted with my morbidelli A504 got floppy disc from scm in england who were a great help. Thanks for all the help from ye.

[Didoto]

Hello, I have been setting a RS232 connecttion to old Morbidelli AUTHOR 1500 using the Windows built-in HyperTerminal and the cable connection mentioned by CNCRouterMan(three wires)

Bits per second 9600
Data bits:8
Parity: None
Stop bits: 1
Flow Control: None

I would suggest lower transfer rate if cable is unshielded or/and longer than 5meters.
I have managed to transmit files from the machine to PC with no problem using this setup BUT there is some weired "bug" when trying to transmit from PC to the machine: I have to set the machine to get the file named XXXX.PGM and wait about a minute before send the file from HyperTerminal, otherwise I get message saying "illegal message format" or transfer cancelled by the other side.
If you know how to resolve this issue please let me know, THANK YOU

[posedi]

Hi,
I have Morbidelli with Tria 6000 control, how can I transfer program file from my PC to CNC?

[rofiksumartopo]

Hello all guys, I'm beginner using the morbidelli tria 7500. this is second hand machine just finished install all the electricity. I cannot going forward operate this machine because on the monitor said: "plc block, error 000"
would you please give me information what should I do? many thanks for the respond.

[CNCRouterMan]

rofiksumartopo It sounds like you lost your plc perameters because of battery back up dead. Replace the battery and call SCM about sending you the plc perameters file and steps to load back into system.

[milos.k]

any information, please!

[unleash_jad]

rofiksumartopo It sounds like you lost your plc perameters because of battery back up dead. Replace the battery and call SCM about sending you the plc perameters file and steps to load back into system.

I'm having the same exact problem now, the battery died and the parameters are gone! Will SCM give me the parameters for free?

[milos.k]

Hi everyone
I have Morbidelli author 504 (1994) and manual is in italian. maybe anybody has manual in english? pleeeease, help! thank you in advance

[prestizdizajn]

Milos mozebi e najdobro da go skeniras toa upatstvo sto go imas na italijanski i da go pretvoris vo jpg file a potoa so konvertor da go pretvoris vo word dokument i postavigo na online translator.Jas imam Morbideli autor 510 i na francuski e ima mnogu malku podatoci vo nego Pisimi na [email protected] POZDRAV

[NazZ]

Hi everyone
I have Morbidelli author 504 (1994) and manual is in italian. maybe anybody has manual in english? pleeeease, help! thank you in advance

Greetings,
I hope this email finds you well.
Just purchased a 1995 Morbidelli 504 CNC machine. I don't have the manuals but still can't work out how to home it.
If someone could give me a few directions it would be much appreciated.

Kind Regards