586,822 active members*
3,270 visitors online*
Register for free
Login

Thread: V2XT 19" lcd & Stainless panel

Results 1 to 5 of 5
  1. 06-16-2008, 05:32 AM #1
    9 1/2
    9 1/2 is offline Registered
    Join Date
    Jan 2007
    Posts
    129

    V2XT 19" lcd & Stainless panel

    Hey gang, here's a picture of my 19" lcd retro fit to my V2XT. I just finished cutting out the stainless panel. Did all the lettering on the mill as well. Too bad I didn't think to do the "start" "enable" etc etc lettering too.........

    (chair)

    Peace

    9 1/2
    B.C.I.T. Machinist CNC
    Reply With Quote Reply With Quote
  2. 06-16-2008, 01:38 PM #2
    AquaEv77
    AquaEv77 is offline Registered
    Join Date
    Mar 2008
    Posts
    17
    nice
    Reply With Quote Reply With Quote
  3. 06-16-2008, 02:15 PM #3
    Al_The_Man's Avatar
    Al_The_Man
    Al_The_Man is offline Community Moderator
    Join Date
    Dec 2003
    Posts
    24223
    Nice Job:rainfro:

    BTW, did you put any protective shield over the LCD?
    Al.
    CNC, Mechatronics Integration and Custom Machine Design

    “Logic will get you from A to B. Imagination will take you everywhere.”
    Albert E.
    Reply With Quote Reply With Quote
  4. 06-17-2008, 01:03 AM #4
    9 1/2
    9 1/2 is offline Registered
    Join Date
    Jan 2007
    Posts
    129
    Thanks guys. I'm probably going to pull it off and put the other lettering on it. The felt pen is sort of an eye sore.
    Al, i didn't put any cover over the LCD. At this point, there is no coolant or other issues getting over there. What do you recommend? Do you think "window film" would work? You know like the oil change stickers?

    Owen
    9 1/2
    B.C.I.T. Machinist CNC
    Reply With Quote Reply With Quote
  5. 06-17-2008, 03:32 AM #5
    Al_The_Man's Avatar
    Al_The_Man
    Al_The_Man is offline Community Moderator
    Join Date
    Dec 2003
    Posts
    24223
    I use a material recommended for use with shop LCD's it is Acrylite FF P-99 anti-glare finish.
    I usually buy it by the 1/2 sheet, but a local plastic supplier may oblige with a smaller piece.
    Al.
    CNC, Mechatronics Integration and Custom Machine Design

    “Logic will get you from A to B. Imagination will take you everywhere.”
    Albert E.
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. I NEED a V2XT DX-32 " User Manual " BAD!!!
    By v488 in forum Bridgeport / Hardinge Mills
    Replies: 4
    Last Post: 03-17-2008, 11:53 AM
  2. V2XT error message "DRIVE FAULT detected (0,z,y,x) check log"
    By rfdoyle in forum Bridgeport / Hardinge Mills
    Replies: 4
    Last Post: 10-08-2007, 09:35 PM
  3. How/what machine to shape a thin stainless plate to become a "half" egg shape ?
    By Calico in forum MetalWork Discussion
    Replies: 5
    Last Post: 03-24-2007, 03:40 PM
  4. V2XT Control Panel Updates
    By NEATman in forum Bridgeport / Hardinge Mills
    Replies: 0
    Last Post: 10-06-2006, 05:32 AM
  5. Wanted; V2XT way wiper " the rubber one"
    By v488 in forum Bridgeport / Hardinge Mills
    Replies: 1
    Last Post: 02-12-2006, 07:05 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules