586,375 active members*
3,627 visitors online*
Register for free
Login

Thread: G code / mach 3 question

Results 1 to 4 of 4
  1. 11-07-2007, 12:32 AM #1
    contractdesign
    contractdesign is offline Registered
    Join Date
    Jun 2006
    Posts
    53

    G code / mach 3 question

    Could someone please explain what needs to be connected, configured, or setup for the M8 code to enable my coolant system. I am using a PDMX-122 breakoutboard with Mach 3. Any feedback would be greatly appreciated.
    Reply With Quote Reply With Quote
  2. 11-07-2007, 04:30 AM #2
    keebler303
    keebler303 is offline Gold Member
    Join Date
    Jan 2006
    Posts
    2985
    I think you might need a macro? not sure. You will surely get further by asking in the mach forum, as it is an issue with software, not the machine.

    Matt
    Reply With Quote Reply With Quote
  3. 11-07-2007, 03:11 PM #3
    ger21
    ger21 is offline Community Moderator
    Join Date
    Mar 2003
    Posts
    35538
    You should just need to set up an output pin to turn on the coolant. I don't have Mach3 installed here, so can't check until later. Also, you need to assign the output pin to the M8 command, I think. Should all be in the ports and pins page.
    Gerry

    UCCNC 2017 Screenset
    http://www.thecncwoodworker.com/2017.html

    Mach3 2010 Screenset
    http://www.thecncwoodworker.com/2010.html

    JointCAM - CNC Dovetails & Box Joints
    http://www.g-forcecnc.com/jointcam.html

    (Note: The opinions expressed in this post are my own and are not necessarily those of CNCzone and its management)
    Reply With Quote Reply With Quote
  4. 11-07-2007, 03:41 PM #4
    mxtras
    mxtras is offline Gold Member
    Join Date
    May 2005
    Posts
    1810
    Check also the spindle set-up page in the config screen. There are two places you need to screw with to get this to go - one is the pins and ports (output) and the other is in the spindle set up screen, believe it or not.

    Scott
    Consistency is a good thing....unless you're consistently an idiot.
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. Help! need someone to help w/ some mach 3 g code programming
    By sconklin in forum Mach Wizards, Macros, & Addons
    Replies: 2
    Last Post: 07-01-2010, 01:53 AM
  2. dxf to g code coverter for mach 3
    By rbyrer in forum MetalWork Discussion
    Replies: 2
    Last Post: 06-29-2007, 12:33 AM
  3. g code and Mach
    By andrewbishop66 in forum Mach Mill
    Replies: 0
    Last Post: 03-16-2007, 01:04 AM
  4. Mach question
    By cncman2 in forum Mach Software (ArtSoft software)
    Replies: 0
    Last Post: 03-31-2003, 07:42 PM
  5. Mach 1 question
    By cncadmin in forum Mach Software (ArtSoft software)
    Replies: 2
    Last Post: 03-31-2003, 07:36 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules