[posedi]

Dear all!

Recently I had ram parity error (base0) error on this machine. Battery was never changed so memory was cleared and I lost all the parameters! Therefore, I cleared all the memory and I entered again by hand all the parameters. Machine started now without alarm but I cannot enter parameters from 9000-9020, 9100-9139. This parameters are important because number of axes are stored there etc. Now I have number of axes by default: 1, so I can drive only one axe )
I called Fanuc guy and he said that it requires a password for this parameteres. What kind of password?? Where to enter?
Also, on papers I found some timers and I entered them also. What about counter, keeprly, Data table data? Does anyone knows how looks like printout of this additional parameters? What else I have to enter in the machine, what to take care of?
Thank you very much!

[Mitsui Seiki]

I have a backup of parameters,pitch,etc. for my 15M at work.Maybe you can used those.You transfer them to the machine the same way you transfer programs.And I don't think you need a password.I know I don't.

[Al_The_Man]

Here is PDF sheet to load Option p
Al.

[posedi]

Thank you very much, I already downloaded this from some site. My problem is that I have this option parameters only as hardcopy! How to insert them?
When I try to edit them, it says "parameter locked".

[zavateandu]

Thank you very much, I already downloaded this from some site. My problem is that I have this option parameters only as hardcopy! How to insert them?
When I try to edit them, it says "parameter locked".

the parameters with 900 must be enetred in IPL screen in hexa mode ex:1a,2c,3f etc
also you need the 3 passwords (secret code)to enter the 900 parameters

[memoryman]

Not true.
You can send all the nc parameters through the serial port (including the options) turn on ALL bits in setting parameter 8000. This may not work on controls for certain export markets.

[jamsari]

sorry, do you have all the parameters of FANUC 15. may I ask hardcopy pdf document. I ask for help because I have lost my documents .. please share
sorry thank you for your help

[dhinakaran]

Hi
I am using fanuc 15M and i cant key in optinoal parameter in ipl mode
Please send me the procedure to key in optional parameters if any one have it

[Pesekstyle]

Hi, i have a 15T, may i ask for the parameters to. I can`t find the parameters for COUNTER and KEEP RELAY.
Where do i have to input the parameters for Timer (Sub24)?

Tnx, best regards,
Daniel

[Pesekstyle]

hi, i have a 15T model, could you please send me the backup. i wont to compare the parameters and see what i am doing wrong.
Tnx a lot.
Daniel

[Mahesh63]

I have a backup of parameters,pitch,etc. for my 15M at work.Maybe you can used those.You transfer them to the machine the same way you transfer programs.And I don't think you need a password.I know I don't.

What is solution ??

[Al_The_Man]

I believe you can type them into a file the same format as in the PDF file.
Al.

[posedi]

You say, I upload parameters as they are now, edit file, and then download corrected file back to machine? It will work?

[F.Sharifi]

You say, I upload parameters as they are now, edit file, and then download corrected file back to machine? It will work?

Hi !
i send you messages please check and reply me soon !

F.Sharifi

[Al_The_Man]

You should be able to download back to machine as per the PDF.
After no 12 in the PDF it should state wait for READ to stop flashing.
Al.

[F.Sharifi]

Dear Posedi

some Fanuc 15 M , needs to SECRET CODE , Via IPL screen to enter the 9000 series machine parametre , however if you check the way desciption by AL you can do it , but dont forget you can translate the hardcopy with any windows editor , and send the file to machine . i have secret code ! i f you need it let me know i type it with the procedure for you !

however if you have still problems please let me know because the procedure on PDF is not easy for anyone that not goodenough exper per Fanuc 15M .

thanks
F.Sharifi

[memoryman]

When setting PWE, turn on ALL bits insetting param 8000.
Read the parameter file through the serial port and all locked parameters will be inputted, even though it warns you.
Cycle the power for the changes to take effect.

[VIESK7]

Do u still have the secret code?

[viorel26]

Recently I had ram parity error on Fanuc O-TD. I cleared all the memory and I entered again by hand all the parameters. Machine started now without alarm but I cannot enter parameters from 10000.
I entered all the parameters from 0001 to 8xxx but I have on my papers parameters 10000, how to enter?List of parameters on machine end to 8xxx.
Thank you.

[email protected]

[rks031]

Dear all
Pl let me know the procedure to download the parameter in GE Fanuc 15M system, we procure one used m/c there was no any battery in the system therefor all data lost, pl help us.