[victormegon]

The parameters contained in the diagnostic file sent by the manufacturer are as follows:

N10300 P 00010100
N10301 P 00000000
N10302 P 01101011
N10303 P 00101011
N10304 P 00000011
N10305 P 00010100
N10306 P 00000000
N10307 P 10000000
N10308 P 00101011
N10309 P 00000001
N10310 P 00010100
N10311 P 00000000
N10312 P 10000001
N10313 P 00001110
N10314 P 00000000
N10315 P 00000010
N10316 P 00000000
N10317 P 10000011
N10318 P 01001111
N10319 P 00000000
N10320 P 00000010
N10321 P 00000000
N10322 P 00011100
N10323 P 00101001
N10324 P 00000000
N10325 P 00000001
N10326 P 00000000
N10327 P 11010001
N10328 P 01001101
N10329 P 00000000
N10330 P 00001000
N10331 P 00000111
N10332 P 11100010
N10333 P 00011100
N10334 P 00000000
N10335 P 00010100
N10336 P 00000000
N10337 P 01101011
N10338 P 00001110
N10339 P 00000000
N10340 P 00010100
N10341 P 00000000
N10342 P 00100110
N10343 P 00111110
N10344 P 00000000
N10345 P 00101000
N10346 P 00000000
N10347 P 10110111
N10348 P 00001010
N10349 P 00000000
N10350 P 00010100
N10351 P 00000000
N10352 P 00101111
N10353 P 00101001
N10354 P 00000000
N10355 P 00000100
N10356 P 00000000
N10357 P 11000100
N10358 P 00111110
N10359 P 00000000
N10360 P 00001010
N10361 P 00000000
N10362 P 00111110
N10363 P 00111110
N10364 P 00000000
N10365 P 00000000
N10366 P 00000000
N10367 P 00000000
N10368 P 00000000
N10369 P 00000000
N10370 P 00000000
N10371 P 00000000
N10372 P 00000000
N10373 P 00000000
N10374 P 00000000
N10375 P 00000000
N10376 P 00000000
N10377 P 00000000
N10378 P 00000000
N10379 P 00000000
N10380 P 00000000
N10381 P 00000000
N10382 P 00000000
N10383 P 00000000
N10384 P 00000000
N10385 P 00000000
N10386 P 00000000
N10387 P 00000000
N10388 P 00000000
N10389 P 00000000
N10390 P 00000000
N10391 P 00000000
N10392 P 00000000
N10393 P 00000000
N10394 P 00000000
N10395 P 00010100
N10396 P 00000000
N10397 P 00010110
N10398 P 00000000
N10399 P 00000000
N10400 P 00000001
N10401 P 00000001
N10402 P 00000010
N10403 P 00000011
N10404 P 00000100
N10405 P 00000101
N10406 P 00000110
N10407 P 00000111
N10408 P 00001000
N10409 P 00001001
N10410 P 00010000
N10411 P 00010001
N10412 P 00010010
N10413 P 00010011
N10414 P 00010100
N10415 P 00010101
N10416 P 00010110
N10417 P 00000000
N10418 P 00000000
N10419 P 00000000
N10420 P 00010110
N10421 P 00000000
N10422 P 00000000
N10423 P 00000000
N10424 P 00000000
N10425 P 00000000
N10426 P 00000000
N10427 P 00000000
N10428 P 00010110
N10429 P 00000000
N10430 P 00000001
N10431 P 00000000
N10432 P 00000000
N10433 P 00000001
N10434 P 00000000
N10435 P 00000000
N10436 P 00000000
N10437 P 00000000
N10438 P 00000000
N10439 P 00000000
N10440 P 00000000
N10441 P 00000000
N10442 P 00000000
N10443 P 00000000
N10444 P 00000000
N10445 P 00000000
N10446 P 00000000
N10447 P 00000000
N10448 P 00000000
N10449 P 00000000
N10450 P 00000000
N10451 P 00000000
N10452 P 00000000
N10453 P 00000000
N10454 P 00000000
N10455 P 00000000
N10456 P 00000000
N10457 P 00000000
N10458 P 00000000
N10459 P 00000000
N10460 P 00010100
N10461 P 00000000
N10462 P 11101110
N10463 P 00101011
N10464 P 00000001
N10465 P 00000010
N10466 P 00000000
N10467 P 11110001
N10468 P 00101011
N10469 P 00000000
N10470 P 10000100
N10471 P 00000011
N10472 P 01001000
N10473 P 00000000
N10474 P 00000000
N10475 P 01110010
N10476 P 00000000
N10477 P 00000101
N10478 P 00000000
N10479 P 00000000
N10480 P 00000001
N10481 P 00000000
N10482 P 00000000
N10483 P 00000000
N10484 P 00000000
N10485 P 00000000
N10486 P 00000000
N10487 P 00000000
N10488 P 00000000
N10489 P 00000000
N10490 P 00000001
N10491 P 00000010
N10492 P 00000000
N10493 P 00100000
N10494 P 00000000
N10495 P 00000000
N10496 P 00000000
N10497 P 00000000
N10498 P 00000000
N10499 P 00000000

And as it says in the parameter restoration touch, I first enter the parameters from 0 to 38 (The Fanuc coach we spoke to said from 0 to 38, not only parameter 38) , then the 900 and then the 552 (RS232 11- 9600 Baud rate).
Then we turn off the control, turn on the control and send the parameters from the PC successfully, but the diagnostic parameters cannot be written manually or sent from the PC. The position of the key of the control panel, I have put it in both positions and nothing.

Attachment 504622

Attachment 504624

Attachment 504626

[victormegon]

What is true is that in the manufacturer's parameters, the number 380 comes with a value, which blocks the writing of parameters if you put the value that comes from the factory.
380 = 00010000
I've changed it to 380=00000000 Because if not, it doesn't allow you to write anything in the parameters and sometimes I modify the 700 parameters for the travel limits if I machine parts that may collide with the machine's guards.

Attachment 504630

Apparently, this parameter to 0 disables the physical key of the machine's control panel by ignoring its position or leaving programs unprotected.

It is true that in the procedure for sending the diagnostic parameters, it defines that the "EDIT" mode must be selected for the sending of the diagnostic parameters, but the only way in which the reception can be activated is with ESTOP pressed, which would be in MDI mode

[zavateandu]

check in diagnose the G122.3 if it is really 0

[victormegon]

check in diagnose the G122.3 if it is really 0

Ok tomorrow I'll look at it. The problem is that it can't be modified. When you talk about 122.3 to 0 would it be 122=00001000 for example? Does that 1 have to be 0?

[victormegon]

Attachment 504632

[victormegon]

check in diagnose the G122.3 if it is really 0

That photo of parameter 122 is after a "RESET" + "DELT" + POWER ON. Even then, it doesn't let you manually edit the Diagnostics parameters. Tomorrow I'll re-enter the 900 and send the general parameters and check the 122 parameter.

[victormegon]

Hello.
I found this thread in another forum where it talks about a "lock key" in "operator panel" but I don't quite understand where it can be.

"reloading Hardinge vmc1000II/Fanuc omd pmc data" Search for the name of the thread if you are interested. I can't put the name here because of the rules...

Attachment 504646

Attachment 504648

I have tried with all the options in "ON" and with all in "OFF" and nothing.I have asked the manufacturer again, who has not yet told me anything about the blocking of the diagnostic parameters 300-499

[victormegon]

In the end, we couldn't enter the parameters because it's impossible to write them. The manufacturer has sent instructions to enter the parameters as we are doing and you can't. The G122.3 parameter is set to 0 and does not change when the key is moved, but in the electrical diagram of the machine it says that the key is seen on the x8.6 and the technicians of Fanuc Spain say that if the G122.3 is not set to 1, it does not allow the diagnostic parameters to be written. The 905 parameter that defines the type of PLC it has, cannot be changed to any type (I think it would be G122 00000001 type L) but it does not allow you to put any value. My question is: if I change the control to a used one, would the machine work with the manufacturer's parameters? I saw on a forum that he changed the two EPRONs to ones supplied by the manufacturer and the machine worked. What would I need to change in order to run the machine? I'm desperate. I need help