[Turbo442]

Possibly this could work as a high speed spindle motor on a G0704.

300W spinlde motor and 52mm spindle fixture/ spindle motor/ DC motor-in DC Motor from Machinery on Aliexpress.com

At 52 mm it could fit inside the quill if one wanted with an adaptor. Otherwise one could hang it on the side with the included bracket.

[Turbo442]

Here is another spindle motor but this one says 57mm diameter. Will still fit in the 60 mm quill and run off the stock grizzly speed controller. This will get you up to 8000 rpm with an ER11 chuck.

Use this motor for small cutters, switch back to the stock motor /spindle for hogging steel.

Technical parameters
Baby details of technical parameters
Can be used for carving metal or non-metal materials
Radial runout of about 0.01-0.03:
Working voltage: 12-110VDC
Power: 300W
Speed:110VDC3000-8000r/min
Torque:4000 g / cm
Insulation resistance: >2me
Dielectric strength:400V
Diameter:57mm
The chuck portion length: 40mm
Chuck diameter : 16MM
Chuck: ER11 chuck with 3.175sandwich
Motor total length:220mm
Spindle weight:1.6 kg
The tail with a cooling fan

Aliexpress.com : Buy Free shipping! CNC engraving machine spindle 300W from Reliable Spindle suppliers on Stepper motor Asian resources

I don't understand where the wires run though.... Through the fan blades?

[Turbo442]

This 2 axis setup is kinda cool. Looks like it includes driver boards as well. I'm confused by the size and weight though. The connector in the photo is probably 1" long but the shipping dimensions are 7.87in x 3.94in x 3.94in.

Packaging Details
Unit Type:
piece
Package Weight:
5.0kg (11.023lb.)
Package Size:
20cm x 10cm x 10cm (7.87in x 3.94in x 3.94in)

Aliexpress.com : Buy Free shipping! CNC engraving machine stepper motor driver board rotation axis A axis B axis fourth axis and fifth axis from Reliable Axis of rotation suppliers on Stepper motor Asian resources

[Connor]

Here is another spindle motor but this one says 57mm diameter. Will still fit in the 60 mm quill and run off the stock grizzly speed controller. This will get you up to 8000 rpm with an ER11 chuck.

Use this motor for small cutters, switch back to the stock motor /spindle for hogging steel.

Technical parameters
Baby details of technical parameters
Can be used for carving metal or non-metal materials
Radial runout of about 0.01-0.03:
Working voltage: 12-110VDC
Power: 300W
Speed:110VDC3000-8000r/min
Torque:4000 g / cm
Insulation resistance: >2me
Dielectric strength:400V
Diameter:57mm
The chuck portion length: 40mm
Chuck diameter : 16MM
Chuck: ER11 chuck with 3.175sandwich
Motor total length:220mm
Spindle weight:1.6 kg
The tail with a cooling fan

Aliexpress.com : Buy Free shipping! CNC engraving machine spindle 300W from Reliable Spindle suppliers on Stepper motor Asian resources

I don't understand where the wires run though.... Through the fan blades?

Installing inside the Quill? Would be kinda hard to switch back and forth. I would prefer a secondary spindle mount and leave the existing stuff alone. Not to mention if you've done a ATC and Power Draw bar...

[Turbo442]

My stock spindle slides out with by loosening one screw. Takes 20 seconds. But hanging it off the side works just as well too.

[Connor]

My stock quill slides out with by loosening one screw. Takes 20 seconds. But hanging it off the side works just as well too.

Photos of how yours is setup?

[Turbo442]

Here is my setup. Baldor 1hp, 3 phase, 2 pole motor , on 2 hp vfd. Spindle bearings and grease upgraded. Motor mocked up at the moment, seeing if I can use the gearbox still. I think most of the noise on this machine comes from the spindle rattling around in the splines. I think I am going to machine in a plastic spacer that slides in between the spindle shaft and splines. Like the one Hoss printed recently.