[gio666]

Also still have a 40x48 or 40x60 Predator machine in stock like one in video

PredatorCircleProgram - YouTube

[ngr1]

So more pictures of the predator for those who are thinking about it. Easily cutting aluminum in a vise or on the table top.

[gio666]

So more pictures of the predator for those who are thinking about it. Easily cutting aluminum in a vise or on the table top.

That looks good, did you get spindle cable into small cable chain with all other wires?

[gio666]

30X48
Attachment 211406

[gio666]

New 4th axis , 5 to 1 reduction ,3 inch jaw or 4
Attachment 211414

[gio666]

Have free shipping to USA only on Raptor machines

http://www.xzerocnc(dot)com/forum/sh...ptorXZ-pricing

[gio666]

Venom machine will have the extrusion extruded second week in JAN.

Also extrusion for a V-groove low cost machine with Thomson rails and 80x80 aluminum . No bolt on steel plate . Belt drive, or ballscrews .

Will be selling extrusion on their own also for the DIY-ers

[gio666]

Uprights for Venom are 10 inch wide,3 inch thick and 8 inch wide bolting to backing plate . It is going to be a heavy duty machine.
Casted and machined all in Canada

[gio666]

This was what the first drawing was. But could not get it done in North America
Attachment 213618

After 5 new drawing, this is the final. 0.0125 at 12 feet for flatness with out machining

[gio666]

Now have the Leadshine MX3660 and Nema 34 or 23 motor kits for the Venom machines
Attachment 213684

Features

Power up to 3 stepper motors of NEMA 17, 23, 24, or 34
Sophisticated stepper motor control based on the latest DSP technology
Built-in breakout board and I/O’s
Step & direction Control
200 KHz maximum frequency for each axis
20 - 60 VDC supply voltage
1.45 - 6.0A output current per axis
8 micro step settings: 1, 1/2, 1/4, 1/8, 1/10, 1/16, 1/32, 1/64
8 output current settings: 1.45, 2.08, 2.72, 3.37, 4.05, 4.72, 5.35, 6.0 A
Damping and anti resonance
Allowing individual output current & micro step settings for each axis
Input pulse smoothing for less jittering, higher torque, and quicker response
Extra low motor heating & noise
Extra smooth motor movement
Simple micro step & output current configuration via DIP switches
Fault output
Compact size and easy setup
50% automatic idle current reduction

[Bx3mE]

Now have the Leadshine MX3660 and Nema 34 or 23 motor kits for the Venom machines
Attachment 213684

Features

Power up to 3 stepper motors of NEMA 17, 23, 24, or 34
Sophisticated stepper motor control based on the latest DSP technology
Built-in breakout board and I/O’s
Step & direction Control
200 KHz maximum frequency for each axis
20 - 60 VDC supply voltage
1.45 - 6.0A output current per axis
8 micro step settings: 1, 1/2, 1/4, 1/8, 1/10, 1/16, 1/32, 1/64
8 output current settings: 1.45, 2.08, 2.72, 3.37, 4.05, 4.72, 5.35, 6.0 A
Damping and anti resonance
Allowing individual output current & micro step settings for each axis
Input pulse smoothing for less jittering, higher torque, and quicker response
Extra low motor heating & noise
Extra smooth motor movement
Simple micro step & output current configuration via DIP switches
Fault output
Compact size and easy setup
50% automatic idle current reduction

I guess this driver does not allow for a 4th axis or is it possible with some addon?

Also is there any pricing info coming up on your forum soon? At least an estimated range?

[gio666]

I guess this driver does not allow for a 4th axis or is it possible with some addon?

Also is there any pricing info coming up on your forum soon? At least an estimated range?

No, That driver is 3 axis only.
Just waiting on casting pricing on a few parts ,then i will have totals. But trying to keep Venom 4x4 around $5

[gio666]

Anyone looking for 4 inch longer z axis plates for square railed Z axis send me email. Help for smaller spindles other than tekno.
Also 12 inch travel Z stock on new 60x65 Demon machine,but have a few extra just Z axis for using 6 or 7 inch end mills

[gio666]

Will have info up shortly on low cost 60x60 XZ Eliminator , 20mm Rails and with ballscrew, not low budget v groove bearings or rake and pinion

[DiaLFonZo]

Will have info up shortly on low cost 60x60 XZ Eliminator , 20mm Rails and with ballscrew, not low budget v groove bearings or rake and pinion

Picture..!

[gio666]

Picture..!

They are not done yet, but same as my first support rail machine with lots of changes and bigger rails and frame .Also 58 inches wide Attachment 219030

[DiaLFonZo]

Look nice.
If I could, I would change mine for a predator with spindle...

Envoyé de mon HTC One en utilisant Tapatalk

[gio666]

Both Demon and Eliminator both have single or dual ballscrews, Eliminator is about half price compared to Demon.

[gio666]

Look nice.
If I could, I would change mine for a predator with spindle...

Envoyé de mon HTC One en utilisant Tapatalk

Predator is same machine almost as the Demon. At this time only 4x4 machines. No Predators left

[mkloppen]

Any way to change my Viper X2 into a supported rail on the X axis?
Also how is the 3D printer/milling machine coming along?
Mike