Would anyone happen to have a GPAUF-R (R71598-C) Card? Mine is apparently faulty and before I send it in, I wanted to check to see if anyone on here might by chance have one.
Type: Posts; User: md63825
Would anyone happen to have a GPAUF-R (R71598-C) Card? Mine is apparently faulty and before I send it in, I wanted to check to see if anyone on here might by chance have one.
BMDC test good. Drives will not enable to home machine. Drive tested good. Need assistance troubleshooting reason drives are not enabling.
Did you ever resolve this issue? I'm encountering same problem.
I recently purchased, what should be about a 2000 3-axis EZ Trak mill that has been setting for a several years. The machine powers up and completes the BMDC test but I cannot clear the E-Stop Alarm....
Hey chipslc, your motherboard is a full-size motherboard. My EZ- Trak is a 2000 model and uses a smaller Single Board Computer (SBC) mounted to a passive backplane, so the Advantech MB I shared with...
Chipslc, I got my machine back online today. Followed some of the information found on your original post and had a local computer company replace the RTC. Unfortunately, they did a poor soldering...
Received board today and installed. During software loading, computer requested Sys Parameter files, which I don't have. I used an older version of the software and machine will only run from disk....
Thanks forhire! Forgot about that option. I've made backup drive images of my office computer HD in the past. I'd still like to figure out a good option to load the software from the floppy disk that...
I want to load my EZ Path and EZ Trak software onto some spare Disk On Modules (DOM) via my desktop computer and I'm not quite sure what would be the easiest way to do it. I have a usb to ide/sata...
I want to load my EZ Path and EZ Trak software onto some spare Disk On Modules (DOM) via my desktop computer and I'm not quite sure what would be the easiest way to do it. I have a usb to ide/sata...
Ordered the PCA-6743F-Q0A2E today from Advantech. And I'm gonna load DOS on my DiskOnModule along with the machine software. Should be able to stick it in the machine and go (fingers crossed). I like...
Thanks to both. reabdet21, machine has the original HDD but my plan is to install a DOM. I've got these on my other machines also. forhire, I saw that SBC from Advantec and that's likely the route...
Anyone know a good resource for an older ISA Half-Size Motherboard? I may need one if i can't get the one on my '00 EZ Trak to come online. Replaced RTC and now I've got nothing. Even if I get this...
chipslc. Did you ever resolve this issue? I am dealing with same issue. Replaced RTC with DS12887A and now nothing. I'm concerned the computer tech that replaced my RTC damaged the MB. Solder job...
I have a '95 Romi/Bridgeport EZ Path and I have had some minor issues with some of the electronics. Nothing major. Upon checking some of the supply voltages I noticed that the output voltages at the...
What is the easiest way to exit into the DOS Command Prompt window from the EZ-Path program? Or is there a way to get there during the Boot sequence? I know you can press DEL to exit into the Set-Up...
It is a BLDC motor. I'm just looking at my options for now. That motor is on my z-axis and when that z-axis moves in the positive direction and as soon as it stops I get a POS-ERR. It's only when it...
I just wanted to re-ask the following questions. Does anyone know the original part number and specs for a z-axis encoder that fits the Parvex motor on a Torq-Cut-22? Or does anyone know where I can...
Not sure I have your solution, but for what its worth, I have an older Bridgeport/Romi and had a similar issue with an Emergency Stop Alarm. Come to find out, a metal chip in the wiring harness track...
X-axis homing switch is gummed up. Remove the cover on the backside of the cross slide and you will see the homing switch. If you push on it, it will most likely be stuck. Clean it with some...
Does anyone know the original part number and specs for a z-axis encoder that fits the Parvex motor on a TC-22? Or does anyone know where I can get an equivelent replacement?
Line "Y" 3 Phase
I want to lower and raise the head on my Torq-cut 22 by hand to check if there is any dragging on the ways. Does anyone know of any easy way to do this? I have ran it down a few inches by removing...
Installed a Drive and motor from EMI and still no luck. I can lower z-axis traverse rate and get it to run a little while before it faults.
What are some common causes of a Z-axis over current alarm? I have had the z-axis motor rebuilt and installed a new z-axis drive and I still get a z-axis over current alarm. I can jog the z-axis with...
How can I add a corner radius cutter to my tool library? Not a ball end mill, but an outside corner radius cutter.
You can determine this a few ways (no pun intended). One way would be to take a precision round bar (Turned, Ground, and Polished (TG&P) will work) about 20" or so long and indicate it in at a...
First, what machine?
Next, you'll need to determine if the taper is due to wear on the ways or if the head is out of alignment. Older machines get a lot of wear over time on the ways close to the...
I have a '95 EZPath and would like to remove the Z-axis ballscrew assembly for inspection purposes. And also so I can replace the thrust bearings on the head end and the radial ball bearings on the...