Hello yorkmachining
The FP4MA is a 2 1/2 axis machine.
The x axis has its own motor and servo drive.
The Y axis and Z axis share a servo motor and servo drive and only one or the other can...
Type: Posts; User: deckeldoctor
Hello yorkmachining
The FP4MA is a 2 1/2 axis machine.
The x axis has its own motor and servo drive.
The Y axis and Z axis share a servo motor and servo drive and only one or the other can...
Hello Guys,
It is official Kunzmann is coming to the USA NOW!!
The Eisler family that owns Weiler now owns Kunzmann! You heard it here first.
The official announcement was listed only a...
regards
DD
Hello Kevork,
Sorry to hear you are still having problems.
Can you scan in your electrical prints and email them to me, here drs9293@gmail ?
By you scanning your prints I will have the exact...
Kevork
Yes those are the relays I was referring to.
On some relays they have a rotary dial on the front these are timers, the third relay and the 5th relay from the left have these dials.
...
There is a very slight delay from when you press the control on button the brake for the z axis that holds it from falling until the electronics come on and the servos turn on to hold the Z axis up...
Hello underthetire/Jeff
I am still around.
This past 1.5 years have been way to full of health problems in my family.
Starting with my 80 year old fathers passing in Jan 2011. My 79 year...
Most problems are the encoder cable,motor cable.
The problems are also in the connectors, They suck!!
The pins push back in side the connectors, when the machine vibrates it cause intermitent...
Hello Guys,
As the title states I am looking for operator manuals for DMC 60H mit Siemans 840d Control.
I have sent inquiries to usual suspects in Germany.
But I need the installation manual...
Hello Guys,
I was able to repair a circuit board in the bottom of the operators console.
This board has all operator interface signals going threw it, I found some bad IC's on the board.
Now...
Hello Guys,
I was able to repair a circuit board in the bottom of the operators console.
This board has all operator interface signals going threw it, I found some bad IC's on the board.
Now...
Thank you for your response yours_prabhat.
I am trying to input NC MD parameters.
As I stated in first post have service switch set to 2 and can see the control change the the parameter to...
Siemans 8m Contol
I could use your help please with Siemans 8M here in the US.
I have the PLC and the NC both Running with no ERRORS showing and the service switch in position 2.
I CAN NOT...
I could use your help please with Siemans 8M here in the US.
I have the PLC and the NC both Running with no ERRORS showing and the service switch in position 2.
I CAN NOT enter any Machine...
Majid,
Remove all circuit boards in the operators console,one at a time.
Place circuit boards on non conductive flat surface,use both thumbs and press on all socketed IC's.
See if this makes...
Hello MAJID ,
So does the machine work now?
Regards
DD
Yes the NSP is the ram board that holds your machining programs. You can add wire to this circuit board and place the new battery down in the bottom of the operators console.
This control does not...
Inside the operators console,in the bottom of the console is a battery it looks like 6 AA batteries together,7.2VDC.
Check the voltage in the battery,replace with rechargable battery if less than...
Do you have a RS232 hooked up to a computer?
Regards
DD
First make sure you have current backup of the machines parameters!!!!
Yes must be changed with power on!
Regards
DD
Under the bottom of the operators console there is a brightness knob try turning it and see if the screen appears.
Does the rest of the machine turn on even though there is no screen?
The...
Hello Vlad,
Are you making chips today?
Are you making good parts?
Regards
DD
Hello Vladimir
I thought we got that c going years ago since I never heard from you again.
I have a new direct email for you [email protected].
I also have skype account, my user name is...
Hello Guys,
I have manuals for most Deckels and controls.
Some in PDF format.
You can contact me with a PM or direct sentnermts at gmail.com.
Regards
DD
The batteries that hold the PLC (parameters).
Replace the batteries and reload the parameters.
What control is on your machine?
Is it Siemans 8M?
Regards
DD
More than likely just the drive went bad. Have you tried to swap with another axis and see if the original axis work with the other drive. I have a guy who can repair the drive and he probably has...
ballbar is really not necessary for adjusting the servos,unless you are trying to do very close work or find a problem when interpolating a circle.
There are screens that show you the servo lag...
Sentner MTS (Machine Tool Service) 23 years of service
5859 Bluewater Road
Conway, South Carolina USA 29527
" Deckeldoctors "
Donald R Sentner Owner\President
Phone: 843 397 7607
I have a customer who is in need of some parts or a machine for parts a Sodick A 350 with Mark11 control.
What I need mostly are mechanical parts having to to do with wire disposal.
The cable...