I just left the transformer in cabinet and used the terminal strip and re routed the wires so 1 leg of the 200v and neutral feed the drives and computer circuit. Wish I would have taken pictures...
Type: Posts; User: vertcnc
I just left the transformer in cabinet and used the terminal strip and re routed the wires so 1 leg of the 200v and neutral feed the drives and computer circuit. Wish I would have taken pictures...
When I had my VMC 15 in my residential garage. I just by-passed the transformer and basically ran 230v Single phase to the VFD and made sure everything else had 115V. Ran perfectly fine. It's now...
Please send available files to [email protected]
I used polyurethane caulk that seems to hold up well.
I would change battery while your at it. If you remove power, You will probably have to re-enter parameters.
Same problem here. Checked distributors in my area and they don' t have any stock. So no go for Helical tools for me.
You will also have to un-bolt the z axis cable track and lay it on its side to fit through a 7' overhead door. My guess is the opening is smaller then 7' probably more like 6' 8-10"if it a standard...
My 1st guess would be the battery is dead. Does it hold parameters as long as the power is on, then when powered off parameters need to be reset next power on. Battery is easy to replace with a...
Not a problem, just making sure. Should work with some minor mods on most RF 45 mills. Haven't looked at them in a few years, let me know if you need further info.
What drawings? The ones on the previous page.
Now that's my kind of a garage. Nice.
Just a heads up on my experience with The California Air Tools compressors. I have had a couple. They are quiet, but duty cycle is not great. I ran these pretty heavily on my machining center and...
Cylinder with least resistance is going to move first or faster. If load is not perfectly equal on each cylinder, or internal resistance of cylinders and mechanical components are not exact it will...
I did as ninefinger described. Cut bore of pulley to a fairly tight slip fit over spindle. I cut a keyway in spindle and also pulley. if I remember right it was 5/16 or 3/8 key. Drill and tap...
If servo machine. The first thing I would check is the encoder and or cabling for the x motor.
counter weight pinned and head fastened to table via bracket. If your going through a 7' high overhead door, you have so remove z axis motor and unbolt cable track and lay on side.
I have heard there are differences in the years. Hopefully someone a little more knowledgeable will help. If i remember right somewhere around 95-97 they upgraded controlled to more memory and...
If you are that close to Maritool, you must be in my neck of the woods. Also running a vmc15.
It appeared the tool holders are tapered with a pull stud. At least in the first video
Have bought from Maritool. Great products and customer service.
Here are some reduced shank end mills from MariTool. They are great for deep pockets. https://www.maritool.com/Cutting-Tools-End-Mills-Reduced-Shank-End-Mills/c78_79_219/index.html
I was following this thread to see how the smithy lathe worked out, but after reading in a few places that customer service is lacking, kind of puts me off. If you can't get tech support or...
If you don't want to buy the 10 sheets from home depot, find a local sign shop. They sold me a few sheets. I am with Ray, Colorplast works good for inexpensive enclosure.
Check this thread.
http://www.cnczone.com/forums/fadal/217248-adding-renishaw-probes-tool-setter-wireless-spindle.html
The first thing I would do is power down an try re-seating all the cards. Vibrations from moving may have shifted something.
There's a head casting on ebay right now. I'll have to find the link.
You can get a Fadal VMC 15 under a 80" door, but you have to remove Z servo and cable chain. Isn't very difficult.
I don't have the machine any longer, but still have drawings somewhere, stand-by.
i do not, but a close friend has one. He loves it, His is pretty big, runs a couple machines off of it. Yeah they are a little pricey. I have seen them on craigslist, but not often.
I have done...
Check out Phase Perfect, no noise.