hi there
it sounds like you got a insulation issue, put some silicone realy thick around the connector sand see if this helps.
greetings waltfl
Type: Posts; User: herby08
hi there
it sounds like you got a insulation issue, put some silicone realy thick around the connector sand see if this helps.
greetings waltfl
what program came with the machine ? look if there is a power setting on the layers selected it should be more then 10%
if you need more help send me a PM
greetings waltfl
hi there
for new adjusting the beam if it does not hit a mirror I take a strip of ply and just hold it right in front of mirror #2 does gives you a idea where the beam is going.
then adjust mirror...
hi sasa
it could be windows 10, try to run it with previous version like windows 7, most Chinese manufacturer does not have upgraded there software to windows 10
greetings waltfl
hi there
2300mm its a far way for the beam you need something like a expander lens lock at lightobject marco sells some.
greetings
waltfl
hi there
you probably need to tighten the X axis belt and or the head guide.
greetings
waltfl
hi there
from my experience the flow rate should be around 6 to 9l/minute in order to avoid overheating the tube what could destroy the tube very fast.
to hook up a mA meter is a must to avoid...
could you post a picture from the whole tube this looks strange to me
greetings
waltfl
hi there
first make the ramp test ( put a strip of wood across the table then raise the right side about 6mm up then cut a straight line with 25% power and 10 mm speed then look where the line is...
hi there
I don't quite understand what you need . if your K40 does not cut at least 1/8 ( 3mm) acrylic with 15mA ( never go higher and watch the cooling water temperatur it should never go above...
hi there
first the un sharp lines could be dirty mirrors and lens and out of focus .
the jumping is normal depending on what you cut because every time the laser starts it will jump.
greetings...
hi there
I would go with the AWC708 but the expanded version because the lite version is to restricted ( a cut down from the expanded )
you got lots of help in the lightobject forum
greetings...
hi
post a picture that we can see what you realy got
greetings
waltfl
hi there
the frame X and Y rails need to be square that's most importand!!! you need to check this with a square see picture.
the beam need to be dead center on all four corner of the table....
hi guys
look at your main AC on some machines there are a fuse inside the socket ( see picture)
greetings
waltfl
hi all
I think the problem is after all the mirrors and lens are clean that the airassist is a must. I cut with a old 40W tube ( over 1.700 hours on it) 6mm acryl with one pass at 85% power and 4 to...
hi there
you got a short in the HV wire check the HV wire ( thick red) all the way to the tube connector. dot use it till you found and corrected the failure or you damge or destroy the power supply...
hi there
did you do a ramp test? that's where you take a strip of wood lift the right side about 1/2 inch then cut a straight line. then leave it there and measure the distance from top of material...
hi there
if you mean this clack clack it seams that the motor pulley or one of the other pulleys are loose on the axle or the head connection is loos.
tighten all screws again especially the...
hi buddydog
the lens get clean from the exhaust , I use a 6 to 8 inch 550CFM inline fan from hydroponics on ebay about $ 80 like this
8†Duct Blower Centrifugal Inline Exhaust Fan for Odor...
hi there
I use a airbrush compressor since two years now and it works perfect. but I don't use the cone I use something like the epilog it works much better then the cone, more power.
greetings...
hi there
I have a '40W" laser and cut bamboo all the time the max with air assist is around 5mm with 4 to 6 mm/s speed
greetings
waltfl
hi all
I am in process to finish the xmass cards and need this font, because I have to change the text.
greetings
waltfl
hi there
I did not recognize that you have the Rdcam. ok it looks to me that the page is outside of the printing area try to turn the page 90 degree and see whats happen.
it has nothing to do with...
TRY USING THE RUN PROGRAMS FOR PREVIOUS WINDOWS . DID YOU INSTALL THE SOFTWARE FOR THIS MACHINE WHAT IS IT?
GREETINGS
WALTFL
hi there
format the machine memory this will eliminate any remains sometimes there are bits and pieces left in the memory and block this section.
it also could be a faulty memory chip.
depending...
hi there
like I sayd before to many people you need to tell more what kind you got what motherboard , what software etc, because there so many different machnes out there all called K40 what...
hi there
you need to give a bit more data from your machine , what motherboard, what software, how you connect ( USB?), because there are so many different K40 machines out there
greetings
waltfl
no side issues except the light brown coloring.
I can cut birch ply up to 3/8 inch (10MM) with reduced speed down to 3 to 4mm/s
greetings
walt
hi there
for a regular use the machines mechanic with stepper is useful the optic is useful the tube and powersupply can be used but the powersupply is mostly just analog and you can not use PWM....