It's been a while since I've worked on Fagor but I'm leaning towards an issue with the I/O card in the control or something in machine wiring? If my memory serves me correctly, I believe there's a...
Type: Posts; User: CNCTech25
It's been a while since I've worked on Fagor but I'm leaning towards an issue with the I/O card in the control or something in machine wiring? If my memory serves me correctly, I believe there's a...
Have you tried running single block mode of the program?
Sent from my Pixel 2 XL using Tapatalk
Looks like you've done your homework on the cables and the issue is likely hardware, maybe a bad IC for the rs232.
Sent from my Pixel XL using Tapatalk
On the backside there is a hole that has a reset button in it that you can access with a small screw driver. If that don't work sounds like software got corrupted or bad hardware.
Sent from my...
Yeah those red switches control the screen orientation from what I remember. Not sure if the manual covers how it's supposed to be set
There may be some switches on the back of the screen that adjust orientation, but I honestly don't recall how they're supposed to be set.
Yes, this will work. The parts of the 8025 are the same for each model with the exception of the external i/o board in the case of integrated PLC vs non integrated models. Even the processor board...
Sounds like the z axis position is beyond the software limit. You can verify what the software limits are in the axis parameter table. I wouldn't change the limits, but rather manually (no power to...
Yes, initialize will reset that table that your on back to factory defaults.
The master password is set by the OEM. Fagor should be able to decode the password for you if you provide them the ID password from the software configuration page.
I guess the software is too...
You should be able to load the tables by navigating to each one on the CNC and then if you see load you can then load it into the memory. It's a little tedious to do as you have to go to each menu,...
There may be some files on card a, and that is probably what you were seeing before.
Yeah I don't believe that version supports the backup/restore feature.
You can contact Fagor and see what can be done for a software update, but that may be challenging as the older units used...
Sounds like the software may be too old and not have the back up restore features. Go the diagnosis menu then configuration then software configuration and you can find the software version in there.
8025 does had a format procedure, but the control must boot up. it is a code that has to be entered via the lock/unlock option which is under op mode 6 I believe. The code is pcall, it will revert...
I believe this may be a bad EPROM, specifically the character generator
It's probably an 8055i model. You should start your own thread for your specific problem.
E2000 is emergency error, you will always get that one when something goes wrong, as there is most likely an additional error or two that will better help diagnose the issue. You can arrow through...
Fama, a blown fuse on the power supply wouldn't allow the control to power up at all. That fuse is on the incoming DC voltage. However, that doesn't mean the power supply is to be completely ruled...
My manual says "S or F value too large" for error 34
Sounds like issues with the memory becoming corrupted, hence parity errors, or worse a hardware error they has not presented itself in form of a displayed error yet. Also sound like your parameters...
8055 is modular control like the 8050, where the modules like CPU and axes card mount to a power supply chassis. Monitor is separate unit.
8055i is integrated, but integrated in that the monitor...
What was 605 set to before?
Sent from my Nexus 7 using Tapatalk
If you've verified that connections of fiber optics are good, perhaps it is an issue with the fiber optics board on the drive. Not sure how you would determine if it is issue with PCB, have you tried...
Not entirely true. Last time I spoke with them, they still have parts, but it's just limited support. The product is discontinued and the chances of them getting parts after they use up what they...
Most likely the issue with your display going blank is due to the controller circuit for the CRT. If your screen goes out again, press a button and if it beeps, it's simply your display. If no beep,...
What is the specific error code number?
TO me this sounds like a mechanical issue (possibly motor torque is not enough) or maybe there is a following error on the x axis but is still within alarm limits
Ok, 3 digit error codes relate to the Fagor drive, not the CNC control. What model drive is? The error should be displayed on the segment display of the affected drive.
WinDNC on XP should be no issue. What baudrate are you trying to communicate at? They have to match on the control and WinDNC, I've seen it where the program locks up for a few seconds if they do no...