I have had my mill for over 15 yrs now. I chased alot of issues . I had one problem with voltage long ago . I got the 10 horse Rotary Phase Converter and had to get the voltage stabilizer they...
Type: Posts; User: ammach
I have had my mill for over 15 yrs now. I chased alot of issues . I had one problem with voltage long ago . I got the 10 horse Rotary Phase Converter and had to get the voltage stabilizer they...
Well its been some time now and have finially solved my issues with the Delta 20. It ended up being over voltage problems at my home site. 260 volts in and the Tree was sensitive . Finially got a...
Well , I have been running a Journeyman Tree with a delta 20 and have had min. problems over the years. If You are still having a problem e-mail me at [email protected] . I run Smartcam software thru...
Evening Alex,
I have a 325 Tree with my controllerand have to Reference everything home first off.
If machine is set (.05) on all axiz from home after last run, reference is easy.
Everything...
Just wanted to add that the fanuc board # is A06B-6052-H002
I have a Tree 325 w/ dynapath delta 20 controller.
(2) Problems
One, every so often I can't run the machine due to the alarm (2) comes up .
I have a alarm page for the light pattern and it says...
I have the Tree 325 with the Delta 20 controller. I have to use the tapping holders that have a little spring play to them. They work fine . If you just put a tap in a drill chuck or holder alone ,...
Hi ,
just wondering how you made out with the machine issue. I have the same machine and issues. I have to pull the PIC board and the Procesor board out each time to reset. Is your problem...
Just wanted to know a little more about the caps you replaced and on what boards. I have been having some issues with temps only because I run my tree sometimes when the air conditioner is off and...
Well its been a long road but I finally found the problem I was having. If you have read some of the old threads , I was having a issue with machine just shutting down at any given time . It...
Hi guys , Good reading material here . Just wanted to add my two cents worth on the subject . I have a small prototype shop in my Garage . I work full time as a 2nd mate to a fast Production shop...
Long story short, had to send unit to Dynapath, Ended up being the start up circuit on the Aux board was blown . I paid a small fortune , but when I got it back , installed ,it fired up and it was...
Well sent the whole rack in to Dynapath last week . I have (2) Rotary phase Converters in the shop . (1) strictly for the CNC and the other for the lathe and mill. I had one in the beginning but...
I have owned (2 ) rotary phase converters for over 10 years , Static can be built for cheap not sure about long range quality, but never had a problem with rotary.
Tony
Hi Phil,
Thanks for the reply , I just got a proximity switch in but havn't installed. I can take the power supply off the computer rack . Your thinking maybe the power from the other cabinet...
just caught your article , I have some pics of the one i made up now. In Vacuum Jigs . ( AMMACH ) works great. Cheap
I may have an extra one if its a Drive AXIS card. There are many sites that may have generic brands .Not sure how good THEY are though. Be careful. Will try to get some info for ya .
Tony
Not sure if you can notice but I recessed the cavity deeper in sections of o-rings and spun some .100 dia. bosses in few areas to help keep from sucking down . the o-rings only collapse .01 works out...
Hopefully you can see how i made if you can enlarge the shots. Tank has to hose fittings at top of tank , one goes to the release valve that i made and mounted on table in machine. 2nd goes to pump. ...
Ok guys ,
Took pictures today and lets see if I can show you what I did.
Not sure if I can write once pics are up so bear with me . 1st time sending pics.
Basically I made up my fixture...
Just so happens I'm working with a vacuum plate now . may be able to get some pics of it . New here and have my own problem with a machine . Basically , took a 1" thk. plate that I could shape my...
Hi guy's , I'm new to the CNC zone but have owned and operated the 325 for about 10 years now. I have kept up with the maintenance best I could since buying it used and have not needed to repair it...
I 'm not sure where you stand at this point in time with this machine , but I have one and have had good luck with it . Having some issues with the aux board , lites up sometimes. Let me know where...