Search:

Build your table square and level, use 4 levels and a string line. With two motors slaved together on the gantry , you should be able to shim your rails........jb

Dave sorry forthe hijack of your...

I 0nly have 3, 1/4 X20 fasteners holding each rail at the present time. This will allow be to shim the rails if needed. Keepimg the rail/rack distance was achieved by using an aluiminum T-slot ...

Leo I will try to look that up tomorrow for you. The linear rails are very sturdy. we clamped my rails and then center drilled, drilled, then tapped and screwed them on........jb

leop, I believe that Dnelso has a large surface plate that is level and true. This allows him to use a height guage on roller stand to keep everything level. I ordered my rails predrilled I'm not...

Well Dave, as usual that is pretty dang slick.........Thanks...........jb

Hi Dave, do you have a finished picture of your loading rollers?........jb

When I ordered a mini torch with my MAX 85 I was told that they were discontinued. I was shown how the long torch could be taken apart by unscrewing the body and removing the long barrel and...

Dave if changing to the mini torch would help,..just remove the long section with the rack and you have the mini torch. It may help by lowering the leverage, or by using lesss torch hose. may be...

Neat machine and good results..............jb

A severe case of "overgroovin" If I ever saw it..........great work Dave

Great video Dave. Looks like your new machines are going to work as good as they look ...........jb

Hi Dave. Thanks for the update. I have been looking at plastic mart for a 200 gal plastic tank. This is over $500.00 by the time it gets here. Did you have problem with your plastic tank on the...

Hi Dave, your tables are looking very good. I have no reference for sizes of E-Chain, would you mind telling me the size of what you use? thanks....jb

Thanks for the look at your brake. I need to find a deal on one..........jb

NIce work. How about a picture of your brake?............jb

You can PM me here. I am usually here daily.., if you get a solid cost I'm still in...jb

gurew, any word on the lift clamps ?.................jb

Mike I found it with a search no problem...neat machine. What are you going to do with it?............jb

Mike, I can't see the video, but I would like to............jb

OKC = Oklahoma City

jb,...Bixby, OK

Dave, I have been getting to do a little on my machine. I don't have the benefit of a floor plate like yours and squaring and and leveling is a lot tougher. I used 4x8 tubing because I had it, and...

gurew, My table is small compared to some of the tables here. I'm having trouble finishing it. Health problems are killing me. I have had 13 operations on my legs through the years, and I'm trying to...

No problem. Man there are a lot of small tables being built, good luck. The table I built is 5 wide and 9' 4" inside and framed with 4 x 8 tubing. ....jb

Duh....I copied the wrong ad. Mine are 20T x60T. I'd have to look at the reciept to get the belt length. My motor pully is steel and the 60T pulley is aluminum.....jb


BTW I believe 14X42 is 3:1

Dave that is a very clean and neat build. The nicest I've seen so far.....jb

GUREW, I bought 3:1 belt reduction1 ( Items XL Pulley 42 teeth
1 Items XL Pulley 14 teeth
XL Timing Belt 15mm width 360 mm length
Ratio 3:1 )

from motion tec on Ebay, and they had...

Gurew, My plasma table is about 3/4ths of the way done. I am rearranging my shop to get it in place, and I have some big sheets I need to move around. Oklahomas' weather isn't helping..............jb

I'll go for the teeth, they can always be smoothed if need be. I have a blaster, tig, lathe and mill and my buddy runs an industrial coating shop. But we can do it any way you think best...let me...

gurew, if the price is right I would be in for a few sets for the same reason. maybe it would help with the price of yours ...........jb

Looking good..............jb