Standard Fanuc code will work just fine. Canned cycles are all the same.
Type: Posts; User: MrMazak
Standard Fanuc code will work just fine. Canned cycles are all the same.
Go to the Vardex web site and download the threadmill program generator. Vardex Thread Turning, Thread Milling & Miniature Threading | TM Gen
Post it out for Mazak EIA and use it as a subprogram...
ok, I will say it for everyone else. HUH?
Drills will go to the WorkFace setting for Z and then rapid to cutting depth. Verify it with graphic check first.
Just put the .090 drill in a new unit and start it at Z 4.35
J65 is used to tell the control what sub program to execute.
J66 is used to define the M code that calls it.
So, if J65 is set to 1234 and J66 is set to 25 them M25 would call sub 1234
M202
M902
M300
G110C2
G0C45.
Try
G110 C2
G00 C45.0
It's a programming error. post the code where it hangs up.
Any decent CAM system can output time for rapid and feed for each tool. Tool Data page tracks in cut time for each tool.
Call Mazak parts dept. Have your serial number and you can get any manual for $75.00
216 is probably a feed alarm. Use Inch per minute feed to move Z with the chuck open. Also insert a dwell of 1 second after the M6 and M7 to allow the chuck to actuate properly or you may get an...
Use larger increments in your program. M32b is the cheap bare bones control and has very little look ahead.
Air blast (M50) and air thru the spindle while running are options. That is why you get illegal M-code.
The battery pack is on the FX84A board. (T2 is the same hardware as M2 so board number should be the same) You can purchase the battery pack from Mitsubishi Electric. Get the changing procedure from...
How about telling them not to do it? You don't need a macro you need better supervisors.
This is the restart procedure for T+ EIA programs. I can't find T32 but it should be close. N seq number should have all data to run ie spindle speed and direction coolant codes etc.Hope it helps.
...
Contact Mitsubishi they have an office near somewhere.
Selecting the hole to restart on is not possible the way you are doing it. Program the holes as points and input 1 in the Q data to omit that point. After running the restart set the Q data back to...
No way to switch on 3D or g-code conversion.
Look in the electrical manual. Some system parameters are listed there. Many parameters are not listed because Mazak does not want you messing with them.
The TOOL FILE needs to be set up properly. Below is a T2 Tool File print out. Look at File Number 40 to set a .125 wide OD groove tool. Match the FNO with TNO in the TOOL SET page so it reads the...
Use Vardex tool number or equal: HC75746L13-EI8NPT TM
%
O10(TMINRH CLIMB INCH CYCLES =2)
(Tool diameter = 0.746 inch - Mazatrol Controller.)
G94
G90 G00 G54 X0. Y0.
G43 H10 Z2. M3 S1850
G91...
From Fusion640MT manual Follow this procedure then in MDI input M65 "cycle start" and it should clear the mismatch error. BE CAREFUL with the first tool change after completing this.
10-11 TURRET...
The CMT baud rate is a User parameter on the Mazak control. It is parameter I1<DV1>.
Here is a CMT baud rate table for the I1<DV1> parameter:
Setting Baud Rate
0 19200
1 9600
2 4800...
I don't understand the tool eye thing but if you have one you can measure in MDI. One tool or many tools at once. Refer to your manual for detail. To use M01 before each tool change add M01 in the...
M2 controls cannot run helical programs unless they are programmed in 90 degree increments. Parameters have nothing to do with it.
The spring coupling between the encoder and motor is probably broken. remove the way cover and check it out (with the power off) Grab the ball screw with your hand and turn it back and forth while...
Most M2 controls (E version and older) are setup to run from the Mazatrol tool data. G43 and H_ are not needed and cause problems sometimes. Set the tool length in the Tool Data page like you would...
Change the M30 to M99