Any new updates with the machine? I am back and itching to build again...
Type: Posts; User: cjsamples
Any new updates with the machine? I am back and itching to build again...
JJCNC - I tried to private message you to ask if you had a wiring diagram for the 408. I know this thread is very old but maybe you are still around. I left a message on your visitors messages....
Can you take some photos? There should be more information on them. If you can see brushes then it would probably be servos. Mine were steppers and no brushes could be seen.
Great find 3D. It all depends on how you want to approach things. I had already purchased new steppers, drives and a break out board. You could in theory use the existing steppers as I actually still...
Good to hear the new bearings fixed you up. Might want to look at the micro computers, picked up a great one for less than $160 and it fits in my cnc plasma controller box.
Fully Assembled PC with...
Where the machine will eventually end up the control panel will be turned 90 degrees from the position it is on now so it will not be a big deal. With all of the the things that can be customized I...
No, the jog right button moves in the X+ direction. The controls are on the backside of the machine making the jog buttons seems opposite of the way they should move. From where I stand, when I jog...
Tom,
From where the controls are when I hit jog left, the gantry goes right. And when I jog up the gantry goes closer to me. Can I swap the buttons to reverse the Jog+ and Jog-? The DRO count is...
Ok, Fixed the X, Y in the negative direction. Just so it doesn't drive me crazy, is there a way to swap the KmotionCNC buttons around for X and Y so they will match machine motion? Make the down...
Tom,
The more I look at it the more I realize that the limits are in the correct spot, I believe. If the control box was not were it is then the X and Y axis would be correct at being that corner....
295984
Trying to see if this image was better. This is the THC from ESAB the MB01 board.
Ok,
Making some headway now!! Should I define all of these values in the Kmotiondef.h or in the C program for load?
I am using KmotionCNC at the moment to make sure I have everything working. It...
Tom,
I am having trouble understanding the correct syntax for the programming you wrote.
Move(0, LoadPosition); //start moving fast to Load Position
while (ch0->Dest > SlowDownPosition) ; //wait...
Thought I had read all of the Faqs but I missed a few. Directions working correctly, homing program modified and working. Wish my plasma lift would come in now.......
Next on the list:
1. Figure...
I got the limit switches working. That config and flash screen can trip you up.
Is there an easy way to reverse direction of an axis? My X is always positive but my Y seems to run negative going...
Tom,
I am having an issue getting the Kmotion to see my limit switch. Checking it on the Digital I/O it is showing up on 136 first opto where I put it. It is normally open as that is what ESAB...
Right on the money Tom. I figured it was something I was doing wrong. I had that config page pulled up on your site when you replied.
That one was easy, next one will be much harder......THC.
Chris
Ok,
Followed along the two threads mentioned to help people get started. X Axis win!! now when I was trying to go back and get Y axis under control it just would not work. I had my encoder for Y on...
The only input device it has is a 3.5 floppy and very minimal memory. Some of the shapes says "out of memory". I will look up some of the motherboard specs and see if I can update some of the...
Hey guys, I hope this will be the best place to put this thread as it is a build….sort of. I have exhausted all of the search terms I could figure out and decided it might just be best to make a...
Kiramunch, Did you have the Esab piecemaker 2 by chance? I find myself in pretty much the same boat. I got a great frame and machine but crappy electronics. It will run now but I need something...
Can you let us know how it works out? I would like to build one myself but I haven't kept up with this thread as I should have.
Thanks, Chris.
Hey Matt, Apparently my web host company lost a drive 2 nights ago and they are working on it. My email has been down and they were only able to restore it from a night ago. It figures, 3 years of...
Hey Matt, sent you a pm about your A80.
Thanks, Chris.
Sorry I have been a little side tracked lately. Life and finishing a few projects before I start on another has gotten in the way. Thanks for the information Joe, I am sure I will bend a few ears...
Joe,
Any chance you can put up a post on your build? I have a techno router and want to do the same, Printer/router combo. Found some links but I have a hard head. Extruder, temp controller, 4th...
Nate, if you are running Mach, Check General config and in the middle of the general page, under motion mode, is it marked constant Vel. or exact stop? That button stopped my pause and resume...
Nate,
Did you leave that "off the wall" setting in your VFD or did you change it once you had the first one set? Maybe Mach is looking for a source and doesn't see it. The one set to "Modbus" or...
Mach has a pop-up that tells you it saves X amount of restore points, so maybe it is just a matter or going back a little further. I don't think xml should make it crash, like Lee said.
It is...
Nate,
Go into mach and select "operator" and on the drop down select "restore settings".
Unless you had to reload EVERYTHING, it should restore your settings.