Does anyone know where I can get a Fanuc 12 M programming manual?
Type: Posts; User: tturnbull50
Does anyone know where I can get a Fanuc 12 M programming manual?
Checked them all, seems ok???? This fault is intermittent, runs fine for several weeks then just losses m/c "Z" zero.
Has anyone ever experienced the loss of machine zero reference points? Always seems to be Z zero and about 52>53 mm short of correct point, but no ALARMS caused major crash. This is driving me nuts...
try OSG, have used their drills and taps
OSG do metric taps as well been using them for a while try their website
Have been trying to make a rect. pocket milling macro, so far as below but only if X is greater than or equal to Y, but can be rotated.
If anyone knows of a better way can they please post it.
...
Yes, during tool change when machine crashes tool recovery states move to tc Zero but actually moves to Machune zero difficult to remove tools from arm during this, service engineer doesnt know why...
Fanuc 18 model B
Stevo thanks for the prompt reply already doing it just wondered when the other machines dont require it, got another problem with tool change, on another forum, thanks again
Help needed; Fanuc 18 m, when machine crashes out (at tool change) and tool recovery page states that you need to return to T.C. zero, it actually needs to go to "machine zero" which is rather...
Is there a parameter that allows the machine to restart the spindle etc. after a M01, as the machine I am currently using does not, but another one does.
Try this I use it on fanuc O-m +18 both vert. and horz.
You only need adjust first 6 lines of :4000 it takes care of cutter comp.
T1
M6
G0G54X0Y0S2000M3
G43Z100.H1M8
M98P4000
G0X50.
M98P4000
try this I use it on fanuc O-M + 18
It is in metric but can be used for imperial as well
T1
M6
G0G54X0Y0S2000M3
G43Z100.H1M8
M98P4000
G0X50.
M98P4000
Have tried all suggestions original prog did not have 2 decimal points dont know why it copied like that, but machine would have brought up an alarm if it saw that, when machine stops there are no...
Part of a much larger prog, the rest run fine but for some reason this one doesnt, mostly programmed offine via copy and paste, so loop works but on this one???? just wondered if there was a...
Daewoo, fanuc o-m control,
T100
M6 (TAPPING DRILL 1/4 BSP)
#1 =54
WHILE[#1 LE57 ]DO1 (No OF OFFSETS)
G90 G0 G#1 X0. Y0. S1500 M3
G43 Z100.H100 M8 T101
G83 G98 Z-24.R5.Q14.5.F300
G0 Z100....
When running a programme the machine freezes on a particular tool, after reset, it runs, after pallet change it drills one hole then freezes again, NO alarms. I have tried changing the tool No etc.....
:4001 (HELICAL)
G21 G40 G80 G90
G0 G54 G90 X0 Y0 S2000 M3
G43 Z5.H3
#100 =-20.(FINISH DEPTH)
#101 =10.(RADIUS OF CUTTER)
#102 =30.(HOLE DIAMETER)
#103 =150 (FEEDRATE)
#104 =5.(PECKING...
Try this, I use it on a fanuc O-M system
:5555 (LINK PROGRAM)
#531 =1 (pallet 1)
#530 =54 (G54)
P1111 M98 (Prog No for PALLET 1)
M62(change pallet)
#531 =2 (pallet2)
#530 =55(G55)
P1111...