Thanks Bill and Darek for the help, I had a moment two Fridays ago. It got late and I had too much coffee so I started with the wire cutters and ripped the 5T off of the machine. I got as far as...
Type: Posts; User: Motopsych
Thanks Bill and Darek for the help, I had a moment two Fridays ago. It got late and I had too much coffee so I started with the wire cutters and ripped the 5T off of the machine. I got as far as...
Thanks HillBilly, will try to do the reset thing on power up, I think I even took my socks off and used my toes to press all the buttons at one time to reset. I have zero literature on this thing so...
Here is what the panel looks like on power up
Ok , one more try because I cant give it up. Wasino gangster with 5T , replaced batteries when purchased because owner never did and sunk all parameters. How do I reset alarm and enter the lost...
Thanks for reply, have a Tsugami with 0TC control on it and it works well for the parts I do. Had a service tech look at Wasino and he said about 10,000 for retrofit. I only paid 1800 for the Tsugami...
Guys , Posted several years ago about this machine and have given up on trying to find its problem. It is an old (1979) Wasino Gangster lathe with 5T control. I purchased it and had it delivered by...
Does anyone know of a retrofit for the Fanuc 0tc control so I may upload nc code off of a disc/ stick ? My lathe has the Fanuc cassette reader serial port but I don't have the hardware or software...
Got it up with help from "AL The Man" and "M Controls" on another thread.
Thanks
Jeff
Still waiting to hear from the factory on the damage for the Operator manual. Playing around trying to get the cob webs out on writing programs.
Thanks Again for all the help. I should get the...
Guys, Got the machine up a few minutes ago . After reading m controls post I had to wait for my brain to unfreeze. It has been years since I did any plc programming and I didn't do that much so I...
Al , yes i have the HAND , MDI JOG displayed on the CRT when you toggle the op panel selector and shows on lower right portion of the screen( doesn't always like to react when you toggle the switch...
On power up I get:
0666-15
Servo:9040-05
PMC:1 -A
Not Ready
Move to another screen and I have OT in the right corner of the screen,
open the front cab with the rack and I look on the rack and...
Al , will have to check in morning again. Gave up and started to play with the Wasino. Bad batteries on that one, have to make up packs tonite at home and try power up in am. Good news on the old...
Kevin, Will take some pics Tuesday, seems one of my rats have taken the camera. Will put out some cheese to try to catch them when they show up after holiday.
Thanks
Guys, tried all I can think. Lube sensor jumped out years ago by someone. z axis had over traveled and I hand turned both to make sure switches were clear. Machine has no air , it is a gang type with...
M controls, no offense taken. I don't know much about CNCs and after looking around on the board at other programming questions I know even less! Will try all you guys have been telling me, I had no...
Al will try in AM, maybee your advice and a clear head will come up with something. If not i'll shower it with hot coffee and breath smoke on it as a welcome to my shop!Thanks Again!
Jeff
Al , tried the rotation switching two legs. Will try dropping the input voltage on the transformer Monday. I switched from the 240 tap to the 220 tap but will try dropping to the 200 vac tap to boost...
Hello, new to board and am having problem with Tsugami lathe I just purchased. Rigged in today and went to power up. Runs startup sequence and will not come out of "not ready" on the crt screen....
Ever get anywhere on manuals for this machine? I just bought one and am looking for the machine manual and am having no luck.
Thanks
Jeff
Hello, New to board and have a question on a Tsugami gang lathe with Fanuc OT control. Never operated CNC lathe before , have Bridgeport VMC with Fanuc 21 control so be gentle with me. Just bought...