Search:

i need to put 10 holes on the face. I pilot drill them thru with a .6875 drill, but then
I need to interpolate a counter bore on a 24" B.C at 1.66 inch deep and 1.437 dia. Can use a .500 -.625 end...

i need to put 10 holes on the face. I pilot drill them thru with a .6875 drill, but then
I need to interpolate a counter bore on a 24" B.C at 1.66 inch deep and 1.437 dia. Can use a .500 -.625 end...

Hello dcoupar:

Would you have anything where you have any hole interpolations on the face? I have a situation where i need to put 10 holes on the face. I drill them thru with a .6875 drill, but...

YES. I do intend to use the machine for shafts. 120" long shafts etc.

I also need to turn 40" diameter parts give or take a couple inches. Does MAZAK offer anything to anyone's knowledge?

I NEED TO TURN AROUND THE 40" DIA.!!!! BUT ALSO NEEDS TO BE
HTZL AND NOT A VTL
I have already a Daewoo/Doosan PUMA700 for past 7 years now. Had great success with it. I can turn 35" DIA with...

Call your Sandvik Rep. If you don't know how to get a whole of one call...

Sandvik
customer service
1-800-SANDVIK

I don't know where your located, but you can purchase form DGI supply in...

I have PUMA 700 with Live tooling> Very happy with it !

Comes in handy when drilling radial holes on castings, bolt circles. Not always
the best for time, but it depends on how you set up your...

I changed the scenario a bit today and thought about similar situation but really I guess no different.

I was thinking about a bolt circle pattern around this 3/4 radial hole. How in the world...

I need to put 3 holes radially on a 12" diameter part 120 degrees apart from each other. They are not inline with anything so I can start first hole anywhere.

The drilled holes are thru to center...

See link below.....



http://www.carmex.com/downloads.php?instance_id=18



Left side of page, where it says Mill-Thread software.... click here, download and enjoy.

LOVE IT!!! GOT A PUMA 700LM WITH FANUC 18T CONTROL.

Heavy Metal:

Yes it is possible. Both Exterior and Interior NPT threads. I am not sure what size you want to do, nor do I know what type of threadmill that you have access to, but this is an...

You're probably thinking "What is this guy talking about?":)

I have a job to tackle that is a bit different then the normal than just a NPT Taper thread or Straight Thread. A bit more...

Thanks!

dcoupar:
Thanks for what you posted. That was perfect. Very good explanation and will help.

Bad Dog
As far as Surfcam. It is Velocity 3 version. It does offer Mill/Turn function which I have...

I have a Puma 700 LM w/ Fanuc 18ti. & Live Tool.


1)I have attached a picture of the part that I need to work on. Would you suggest using cylindrical interpolation G07.1 to put the groove and...

1)I have a Puma 700 LM w/ Fanuc 18ti. & Live Tool.
I have attached a picture of the part that I need to work on. Would you suggest using cylindrical interpolation to put the groove and the dimples...

:cheers:

Does anyone have something they could post where they did a rotary axis engraving part on the C-Axis with Surfcam? I also need a Live Tool Post too.

I looking to learn a few things:
...

G-Codeguy is right. It is much easier to just add another block and modify another one. It is easier to diagnose for future alterations, rather than changing signs to accomodate quickly.


ONE FIX...

Try This..... I only changed a couple of things and simulated on NCplot but
it looks as if it will work for you..


%
:1234
T101M8
G97S500M3
G0X0.Z-.1
G65P9003X0.Z0.K3.0B.05W.1C.35A.1F.005

Does anyone know what parameter enables MacroB programming for
Fanuc 18T control?

I actually had this alarm happen to me as well. I pulled off the rear back cover of the turret and there is a proximity switch back there that has yellow led usually or green. Stick your screw driver...

Sorry fella's. I was on vacation. I appreciate your help. It was a mix of two different problems.

1) First... yes you were indeed correct that C90 needed to be C90. with a decimal point. That did...

I have a problem. I am not able to move my C-axis in 90 degree increments in
the following program below. The drilling cycle will work but it seems I am missing something here. It does however...

Any Sample programs with live tooling for Daewoo 700 with Fanuc 18i?

I am looking to start utilizing the live tooling in my machine but would like to look at a format of someone's that has drilled...

First try M78 and M79 in your MDI mode. If you cannot get the quill to advance then check the electrical schematic for your tailstock advance and retract. Find out what number parameter it is and...

I have experienced this problem with a Daewoo 10HC. We replaced the pulse encoder in the machine which fixed the problem. Sometimes the turret would play "wheel of fortune" for 1-2 minutes and then...

You can inject the pin and indujet the pin with M46 and M47 I believe.
If the tailstock is programmable that way. Then you can incorporate these M codes in your program and pick up the tailstock...

150 rpm is about right. I worked for a company where they had a problem running 304 stainless castings and would chip the inserts out and scrap castings. When I got there they were trying to run at...

Please help.....

Looking for a program to do a 3/4"-14 npt exterior thread on a lathe. I cannot figure out from the machinery's handbook how to figure out the "x" number in the 2nd G76 line.........