Hi all,
Just wondering about the following.
At the shop I work a multus u4000 with ops-300sa-h controller and recently my boss bought a second hand multus u4000 with an osp300s-h controller.
On...
Type: Posts; User: duivenhok
Hi all,
Just wondering about the following.
At the shop I work a multus u4000 with ops-300sa-h controller and recently my boss bought a second hand multus u4000 with an osp300s-h controller.
On...
Your right c and h do not have to be both in de G84 block
And the double m53 also isnt nessecery but this shouldnt and doesnt give any problem.
Riged tapping is a standard option on this machine...
Hi all,
I have a problem with rigid tapping on a lathe with life tooling and a fanuc Oi-TF controller.
The machine this occurs on is not very much used even though it is already a year old and...
Tnx 4 your reply
Originally Posted by :
I dont think you can back up these values and reload them later but they must be stored somewhere in windows
well, think again of course, the entire load...
Hi all.
Simple question. Osp300sa
I have a very large program with lots of load monitor values. These are manualy adjusted so that it Works best in my opinion.
In dont want to manualy retyp them...
Thanks 4 your reply.
What i am gonne do is drill a excentric hole about 60mm diameter 50 mm deep and "spiral it out with a 16mm shaft mill to 140mm (might be that trochoidale isnt the whright...
Hello all,
I have a simple question (i think).
I have a multus with OSP-P300 control with IGF.
Does IGF support trochoïdale milling or is it that i didnt search good enough today.?
Thanx for...
hi there.
anyone around here who has experience in the okuma option "turn-cut".
I just got a brandnew multus u4000 but cannot (until now) find any explanation about it.
Maybe someone here got an...
Thanx deadlykitten.
Found it earlier today in the special functions manual
I was told (by my boss)for sure that this option would be functional...... but of course.... nope
Shame but still a...
As far as i know... red blinking is totally inactive...yellow is active with some problems and blue is totally active.
I think m866 and m867 is to temporary disable the CAS but for this it first has...
Hi all,
Been playing around with the CAS on a multus b300w with p200l system.
The casis always disales (red blinking icon in right top corner.
I just cannot figure out how to turn it on. I think...
Hi there.
I am kinda new when it comes to working with sinumerik.
I cannot figure out how to get a iso programmed program to simulate.
The program runs fine on the machine but i have to be so...
Hi there,
Just got an old Monforts Unicen 500 installed at work with sinumerik 840d controll.
I also got a bunch of manuals on a usb stick with the machine, it also contains numerous manuals...
why would you want the tailstock out of the way??
On a LB300 i do facing with the centerpoint only about 2" away from the face of the product, just extend your tool a little bit more from the holder.
why not just try it out stopping the spindle firts.
I always stop the spindle before advancing or retracting the quill.
but have no idea if this would actually give the error you're getting.
parameter 9000 bit 1 (NDP). Needs to be set to 1
@fordav, been to quick in posting LH should offcourse be LT less then and #27 simply be 27 as in less then 27 but offcourse you'd have figured it out alraedy.
#1 = #5042 (remember start Z position)(#5042 = z-axis on lathe, not sure on mill)
WHILE [#5042 TH #27.000] DO1
#1=#1+0.100
G0Z#1
G4 X5 (dwell 5 second)
END
M30
I think the only way is to place "VZSHZ=3" in one of the first lines of the program OR place "VZSHZ=V1" in one of the first lines of every program and input the zero shift amount from the chuck to...
place zeroshift in program VZSHZ=30 shifts your Z-zeropoint by 30mm (or inch)
today i almost faced a workpiece with the center in the work piece.
Is there like M156 M157 (enabeling an disabeling spindel rotation without center in forward position) a posibility to prevent...
maybe you could use "work shift" to calculate your piece zero
put z0 in G54
mdi G54 T0101 G0 U-1W-1
scratch face of workpiese in jog and stay here
[OFFSET], keep pressing soft key right [>] ,...
i think you can only put a text in a #3006 operator message and not show the value of a variable
try #2501=0.222
or
g10P10001Z0.222
@mkd. Do you need more info about how i partionaly manual place the tailstock at accactely te same position so it can be usefull in a series production or was my first post clear enough.
I dont...
Sound like an option but you would have tot be more clear about how to do this.
Manuals arnt mentioning this and i have no clue about how tot do this
Verstuurd vanaf mijn GT-I9300 met Tapatalk
hi al,
got a little problem.
Got a non programmable tow along tailstock with a tailstockclamp wich is a left threathed nut.
I am trying to program the tow along part (with parameters,v100= pick up...
im not that technical and we dont have a technical service in house, so just correcting the lost movement wil do for me.
got it done already.
thanks anyway
hi all
on a second hand LB300M with u100L control my boss just bought today i found a backlash in x-axis of 0.035mm.
Gonne try to compensate it tomorow.
Anyone got a simple explanation on where to...