Solved
The problem was geckos power suply.
Until now it worked on12v, but probably the 12 regulator of power did not regulated the tension correctly (at times i could see 13.2v).
The solution...
Type: Posts; User: cristian gabor
Solved
The problem was geckos power suply.
Until now it worked on12v, but probably the 12 regulator of power did not regulated the tension correctly (at times i could see 13.2v).
The solution...
Hi
I had a chain of problems on my plasma cnc.
My setup was
powermax 1650
servo motors
gecko 320 drives
thc 300
no breakout board
all in one cabinet
hi
It does not work
I installed the breakout board
I get 5v on dir input of the drive coming from it, but it still refuses to work
I set up the motor outputs on the pci parallel port, and...
Hi.
can i use the pc power suply 5v for my geko 320 drive, so i can free space in my cabinnet ? (not the motor power)
Hi
I received today my breakout board
Just made a quick test and i get 5v out on the breakout board corresponding output, unlike from the parallel port, from where i was geting 3.3v out
Hope to...
Hi
The keyboard is working fine, i get those voltages on the paralell port pins while joging from the keyboard.
Hi
I have my cnc plasma cutting machine working for last years ok, but the thc down signal, due to a bad cable.
My configuration is:
Powermax 1650 machine torch
Thc 300
Floating head
Geko 320...
HI
i made the bench test and i solved the problem
i was locking this morning for a variable power suply and i found a variable soldering iron
opened up unscrew the leads that were going to the...
pics
hi
I sorted out the some problem i had with thc 300
it was that i was confused about post file in sheetcam(where i supposed to enter my switch travel)with the tap file resulted from sheetcam...
the xml file
hi
i vave had my plasma table runing for 6 monts on belts
and decided to go for rack & pinion drive. all worked fine until my servos do not engage anymore .
I have a buton on my controller...
HERE ARE SOME OF MY FIRST CUTS
how do i edit g code ?
i soupose sheet cam should not put this code in there is only a cercle on a plasma cutter
thank you john for replaying
it feels that i'm not on my on here trying to...
i found this in a doc that i paid 10 $ on ebay some time back
^^G92 - Programming of Absolute Zero(Do Not Use)
This Code is an old way of programming. You are redefining the
machine coordinate...
hi
sorry for not answering ,busy trying to keep up whit the plasma table and the regular day by day work
"Is the direct drive setup an issue?"
yes it is my axis are jerking and the belt has an...
hi got my machine mouving
i'm hapy about this but is still jerkyng
it seems that i can not load videos here
any help is greatly apreciated
the fault is in the soft somewhere and i soupose
and...
hi
did you find a solution to your problem ?
it seems that i have the same one but on bouth axes and all the time
i need some help
thank you
cristian
hi
did you find a solution to your problem ?
it seems that i have the same one but on bouth axes and all the time
i need some help
thank you
cristian
hi got some progress as you can see in the photos but i have ran in to a problem (see videos ) my axis move in steps (vibrating) the longer i go the harder it vibrates
can anyone help ?
i got...
hi again
i made some more work as you can see in the pics
got the gantry on and sliding wiht ease but if i hold one side fermly i can push the other side about 5 mm max . is this ok or is an...
hi
how is you lincon plasma working ?
how muchy did you pay for it ?
i'm in the midle of my cnc plasma project and i don't know wat to chose
is the THC working on it ?
thank you
CRISTIAN IASI
pics with my work up to this time
some pics in today
what plasma system should i go for?
did any one used "telwin" ?
hi evryone
i plan building a plasma table for cutting 6 to 12 mm thik and 1.75/2.2 m steel plates.
the mobile water bed table should help me loading and unloading the heavy plates whitout the...
wat power must a laser diode have to melt the plastic powder?
i finaly started my first projetc
i ordered a cnc kit 3 Axis CNC Router or Mill Stepper Motor complete kit (ebay)and some of the...
http://www.youtube.com/watch?v=u7h09dTVkdw
it is not better puder then Liquid Plastic
hi very nice i'm planing to build one of them .
is there any one to have any experience about this?
what is the media to print from?
what is the best melting devece
color 3d printing?:)
is there any one using the MULTIPLAZ PLASMA ? i'm about to buy one of them.
does worth the money ?