we just received a new mill,same thing there is not a option to disable door switch to my knowledge in the control like the last machine (2007)
i took a feeler gauge and affixed it with magnets...
Type: Posts; User: timmydabull
we just received a new mill,same thing there is not a option to disable door switch to my knowledge in the control like the last machine (2007)
i took a feeler gauge and affixed it with magnets...
you were just quoted 30 weeks for a new machine from Haas?
shipped to usa?
thats the longest lead time ive ever heard of from Haas.
i got it, i did not realize there was amphenol connector underneath and inside the sheetmetal
connected it and it allowed me to access parameter list
i am getting a 835 v axis serial data...
2017 ST-15 went to install a 2016 servo 300 barfeeder today,after installing the cables,and changing parameters i get a v axis alarm 832, i cannot clear the alarm or get into the parameters to...
call Radwell International they may be able to repair the board for you
good luck
not yet
still waiting
good luck
Looking for someone who can laser scan modify and create solid model of a clutch cover for a motorcycle.
i will need a file ready for me to machine from.
those who are qualified and interested...
i have not run across this problem myself before,seems i seen on another thread someone talking about this,there solution was reloading the system software i belive..
you should start a new thread...
updated news
turns out i cleaned some fine metallic dust from the proximity sensor(s) on the tool carousel and my proble magically went away (so far)
this fine particulate matter came from dry...
lasted 2 days ,i knew i wasnt so lucky,guess i will call hass monday and see if they can ship me some parts.
ill keep you guys updated.
thanks
Hi Geof,
Yes i checked it all carefully,today i removed the relays and reinstalled them and tapped on the motor housing with a rubber hammer and it seems to have a renewed vigor.
maybe the...
check out the clutch to see if it was slipping and it appears to have a keyway lock and does not slip or is not loose.
when the toolchanger fails i normally hear a load on the motor like it is...
ok will do
thank you
i am getting a 113 shuttle alarm on the toolchanger,i notice that the toolchanger is very slow moving toward the spindle and sometimes will stop or hesitate before moving all the way to the right to...
This may sound crazy but check the y axis sensor at the bottom left side of the table and make sure there isnt any chips in there,i get y axis alarms all the time due to this.
your right it was the low voltage powers supply.
thank you so much
on another note i receved a note from my power company that they were in the neighborhood switching out meters that they can...
Thank you Mr Williams,should this occur again i will contact the local HFO and arrange for service..
thank you all for the replies
tim
luckily today i booted up the machine and went thru the spindle warmup with no errors,have also been machining 1 hour cycles on it all day with no problems.
i hope it was just a glitch.crossing my...
thank you i was hoping it wouldnt need a board replacement but after 4 years i shouldnt complain if it did.
been a good trouble free machine for a while now.
thank you for your reply.
tim
anyone ever experience the error "Keyboard not found" on a haas machine?
i noticed during spindle warm up the machine will throw up the keyboard not found error after 1 minute of operation.
i...
if you go to CREATE-CURVE-you will have options to create a curve on various edges.
i always use this on solids and have never tried this on surfaces.
hope this helps
the tool release button on the z axis cover did look a little suspicious. and the connector was covered in goo and could not be seperated.
i will disable the parameter and give sone time to repeat...
for the last couple months i have been experiencing an erratic tool release during power up of the machine or when i push the MDI button.
it happens intermittently and when you least expect it the...
yes there is definatley interest.
i am trying to do something very similiar.
i looked at the machine JC is asking about,this was one of the first vf1 machines built by haas.
back then they did not have chip augers there were ports on each side in the front where you could...
keep in mind this is a 1992 machine with a serial number in the 1800 range
spindle cartridges may have been redesigned since then and that machine may require a special spindle at a special price...
i seen some videos where keyways were being cut on a vmc using a carbide insert on a toolholder using a series of up and down plunge cut motions while inching forward to square up a machined contour....
trade is going crazy lately,2 years ago i would receive a bid from china for 20 cents when usa vendor would bid 35 cents,now i am receiveing bids from usa vendors for 45-50 cents and getting $5-$8...
the majority of the time when i can not see a tool during backplot it is in the design of the tool or a parameter im asking it to do that wont calculate.
Can someone advise me of suggestions of the proccess for creating axial fan blade designs in 3d space.
i have never used these design parameters so i dont know where to start.
thank you in...