Im really rusty, and communications and drip feed was never my strong suit, but I worked for Mori for a long time so I will try and help. Your machine is a mapps 1 or 2 most likely due to the date,...
Type: Posts; User: motionman
Im really rusty, and communications and drip feed was never my strong suit, but I worked for Mori for a long time so I will try and help. Your machine is a mapps 1 or 2 most likely due to the date,...
To the OP.....GREAT NEWS..... As for Mr. Gitrdun..... I once had an Okuma tech in my building for a 30 minute job, it was through the dealer Morris South, They have a 3 hour minimum policy, he fixed...
I am rebuilding a mill with turcite bonded to the bottom of the table, and the saddle. The material does not seem to be worn, but has lost its bond with the component. It is generally on the...
If you have a question about the springs, call SPS in NH, not only do they stock, but have the experience to know what OEM parts were used in most cases.
the bearings are bad
break out the cylindrical square, and indicator, do basic geometry checks first, then come back with results for advice
Sorry, I just saw the year of the machine, this may be correct on the latter models
use shims to push the screw in one direction against a bearing surface
Call Mori back, be polite. Explain that you simply dont have a serial number They need a serial number to start a ticket, before they forward you to an engineer. Be nice, and explain the situation,...
M60 and M61 are the brake commands for a 4th axis.
use the hardest material you have,as they are under imminence pressure
I forgot to pull the eproms, replace eproms with yours and reset jumper for your axis
Well......yeah....like every major tool builder uses this in material as a bearing surface in their machines. Was not trying to be a smart butt, but most machine tool builders use this material.
Are you Shepard629 on ebay? i just sold a 1010-4 today.
Call SPS at 1-800-892-6258 Good people
If they turn the comm, make sure they undercut it as well.
https://www.yaskawa.com/pycprd/lookup/getfile/workspace%26SpacesStore%26f8ca732e-08bb-4669-b3f7-4ffde9bba8f7%26TOE-C843-7.25.pdf
This should be the download link for the manual, it is available...
I have seen this issue on a 15 control with the LCD. There is an aluminum foil reflector for the back light tube that is glued to the backlight housing. The glue separates and allows the foil to...
Glad you got it fixed, in the future another area to check that I have seen many many times is the cable in the pallet change area door switch
Ball screw bearings are usually the first thing to make noise, and generally cheap to replace.
There are just quite simply way too many things that can cause an issue like this .100 is a **** ton of movement, so ifizcnc might be on to something. It would depend on your machining conditions. ...
i agree with above X2
Kurt nothing else
???????????????
You are trying to make chicken soup out of chicken ****
The tool changer on a Fadal is controlled by 2 hall effect switches, these switches require a magnet to energize the switch. These are not inductive proximity switches that can be fooled by chips on...
I agree the component level parts are cheap, and $1000.00 for a servo amp sounds high, BUT sometimes it is not about what it cost to do it, BUT KNOWING HOW to do it. I know Dan at ITS personally and...
Look for a Mori Seiki SL-1 with a Yasnac control, they can be had all day for less than 5K
My Hurco salesman called me today, their (Hurcos) year end is this month, he offered me 20% off if I took delivery by the 31st. I like Kitamura as well, I do not care for the Mazak product line.
I have a company that I work with that can do an on machine regrind if the taper is damaged. email me if you need help with this [email protected]