Can a machine file be created from scratch ? Dose anyone have a generic Fanuc wire post for an Old control say 6m or a 0 controller . Thank you all .
Type: Posts; User: gabedrummin
Can a machine file be created from scratch ? Dose anyone have a generic Fanuc wire post for an Old control say 6m or a 0 controller . Thank you all .
I suspect if its a machine with a 6m controller your U-Axis resolver is starting to have an issue . I would go into the paramters tell the machine its a 2 axis machine and see if the issue gose away .
Depending where you live a lot of colleges offer cnc programming course 40 hour crash course took mine in 86 ish .
Never mind I did a timing belt conversion .
Seems to be related to the cold last couple of day temp has been 70 plus and screen lights up first attempt . I did not think a lcd screen would be suspect to temp or maybe the crt card is ?
Machine has has a Fanuc 0M -A control . One of the first Elox/Fanuc machine to go with ac servo drives .Machine had a 14 inch color CRT originally .Many year's ago I replaced the CRT display with an...
Many year's ago I replaced the CRT display with an LCD conversion .And it has worked perfectly for a long time . Lately the screen wont turn on and I have to repeatedly turn it on turn it off and...
Can any one tell me the pitch and gear count for the x-axis gears that drive the x-axis lead screw .Thank you in advance .
The only parameters that will not auto load are the ones for the digital AC servo drive .Brake motor tension settings . Com. settings. Edm cutting settings . Do you have a manual for your machine...
If the batteries go dead while it was sitting it will lose all its parameters . Change the batteries while the machine is turned on .
Memory short cuts.
Memory all clear Hold 0 and delete...
Acorn is a motion controller .It will send the step and direction signals to the driver . In a closed loop system the controller will correct the step train to make sure a step is not lost . Even if...
How long is it ? Dimension from end to slot ? Taper at what angle ? Dose it need to be concentric from thread to thread ?
If you don't have the cutting data tape you will have have to enter the cutting conditions thru MDI .
How is the water condition ? Have you used wire machines before ? It is a slow process, water condition, guide condition, power feed contacts all have to be in proper condition .Start there.
Looking for dimension for a tool wedge Hurco cnc lathe TM6i Thanks if you can help.
Good luck. I've been looking for one for years . Have seen 3 for sale in the last 10 years and very pricy especially now that everything has an inflated price good luck sir. I settled on a Dayna myte...
[QUOTE=rolfinator2002;826597]Thanks for all the feedback. I'll consider the topic closed then. I think I'll let it fly, and if I get errant finish or dimensions, then I'll rechrome the quill and...
IF YOU DONT NEED TO CUT TAPER GO INTO PARAMETERS AND TELL THE MACHINE ITS A 2 AXIS TURN OF U AND V AXIS. THEN SEE IF TI WILL RUN.
After 6 months problem has been traced to defective motion control card .
Your machine not the correct scale .If its drawing in inches it needs to be drawn in millimeters.
MY machine has about 8 inches of z with the tail stock on and about 12 with it off .
It will travel to the right until the carriage hit's the limit on the back side of the bed . It will travel z- till it crashes into the chuck if you don't stop it . So the limit switch on the back...
With or with out tailstock ? What type of chuck , center, collet chuck are you going to use ?
I was thinking the bearings should be installed like this ?488586
I want to replace my spindle bearings . I know don't do it .But I have a plan . Taking it apart no problem. Re-assembly will be done inside a large plastic bag . I will put the spindle shaft in the...
You are going to need some type of press to do this .Weather is a mechanical or hydraulic you need something to mount the tool in . And drive the upper down or drive the bottom up or both moving...
What will generate the fixed spring pressure ?Are going to try to bolt the blank holder and lower die together with material in between ? Most dies we run 3000 + tools we maintain pressure between...
You better get some springs in there . If you see wrinkling on the finished part that is caused by not having enough pressure between the blank pad and die face . you might need some stand off to...
That is a safety handle for the power . It can be replaced for a standard handle.
485794485796 This cuts taper .