Search:

did you have a tool setter on the machine or the machine had one?The tool setter can block the machine go only in measuring direction
Also can you send a picture with the first diagnose page while...

if the zero return way is on + plus side ,you can increase the limit on paramater 1320 with 999999 ,move the axis in minus direction around 100mm,make the zero return and fater that put back the...

check in diagnose the G122.3 if it is really 0

i never heared in my entire carrier a Fanuc 0-M with aparametrs locked only if you have a hard key switch somewhere to block the PWE=1
Did the PWE is 1?
is the diagnostic binary or decimal format?...

M-Milling
T-Turning
L-Laser
P-Punch
G-Grinder

Fanuc released manuals for Laser and Punching and never for a grinder as the parameters and maintenance is similar to turning and milling

do you want to sell here?i think you are in wrong section
please post problems to help

why do we need them?

Try with the parameter 5003 bit 6 LVC or bit 7 TGC

LVC Offset value of tool offset
0 : Not cleared, but held by reset
1 : Cleared by reset

TGC Tool geometry compensation value
0 : Not...

First you can disconnect the power wires of the motor from the drive and start again the machine
If the alarm is still present,problem is in the drive
If the alarm is not present,the problem is in...

The brake is normally powered with 110v AC and on new machines is build in the motor with 24v DC
When the machine is off,the brake is not powered and hold the axis
When the main contactor MCC is...

yes,you need to atach the pmc file to be read

you can read it over ethernet if the machine has etehernet port

PS059-Program number not found
check the program again if it has the same numer inside of it as outside of name

when you go to IPL menu you just need to press enter for options you want to keep and change the value only for the option you need to change

look in PMC-DATA TABLE,where are the timers,counters,keeprelay

Try it in emergency mode state or go in PMC menu and stop the PMC

On the machine that you want to try the sram and is not loading all 4 files,did you tried to take out the sram?
Even if the machine is not starting you can take out the old sram to see if it is...

you did not attached any photo

When the MCC-main contactor is turned on ,the power supply gets power and turn 7 segment led to 0 and all servos are with "-" not blinking in normal state
so in your case i start looking of the...

As far as i know there is a servo software update also to be made for that new linear scale to work
what type of controller you have? 16i,18i,21i,30i,31i,etc?
what is the version and edition of...

what values you have in these parameters:
2023,2024,2084,2085

there are many software to download but i use from long time CIMCO EDIT for transmission

Use Program transfer tool from Fanuc for file transfer,is a drag and drop software ,it is cheap ,around 20 euro and is the easy and safe way to transfer files between CNC nad PC

First of all say to us if you use the X8.7 or X8.6 signal as skip signal or what wires did you identify and use
Also if you have the diagram from electric book with the page of skip signal please...

First thing you have to do is that when you call T01 you should be sure that the tool is in the center of the spindle and not above or under the spindle line so you know mehcanical the turret is...

Do not say to people is SRAM issue as you do not make the difference between LED 8 with all 4 greens and one from middle second row is RED on and LED 8 with 4 greens led on and on the second row the...

Alarm 8 indicates that the CPU not started,i would recomend to replace the CPU board not the main board

500188

what is the code number of the spindle unit?
is the spindle with 4 digits led in the control PCB and the small yellow case with 4 buttons under it for setting the parameters?
if yes,AL-17 means...

send me an email with some photos of the machine to see how it looks
[email protected]

When you use the load program button,the program is copied to that USB Path 1 folder in the CNC MEMORY
The CNC MEMORY of your machine is indeed 2 MB ,the maxim is 8MB stored in the FROM
if you...