Hello I am having the same error message on my lathe. Which parameter needs to be changed for the turret time functions?
Type: Posts; User: camaro_dan67
Hello I am having the same error message on my lathe. Which parameter needs to be changed for the turret time functions?
I came across a crt screen that I was told was from a Fanuc 15m. I am looking for the pin out on the back of the tube. I am also looking for the heater voltage. It is a 9 inch monochrome unit. The...
Has anyone successfully got this board on ebay to work for the crusader m screen? Or know what needs to be modified to make it work. The instructions they give are simply schematics for the machine...
Transfer all the chips that plug into sockets. I just did this on my 3m not long ago. You may have to do the procedure to reactivate your drip feed chips again.
Thank you I will look into that.
I ran it for a while this morning. Mostly just drilling holes so no accurate position checking yet. I had it going about 45 minutes and before I shut it down I put my hand on the motor and it was...
Tonight I did adjusting using my diagnostic numbers 800 to 802. 800 for x, 801 for y and 802 for z. I started with adjusting the gain on the z servo drive I got the number close to 0 but it was still...
Ok in the book I found diagnostic number 802 says it displays the position deviation amount for the z axis. Does this sound like what I should be looking for?
I'm not sure on my machine which diagnostic I need to look at for this. I do have the maintenance manual that covers some parameters and diagnostics. I'll have to take a good look at it.
The motor and encoder are identical part numbers as far as I know. I didn't pop the cap off of the back of the motor to double check the part number on the encoder.
I tried turning the gain pot...
I have not done any position testing just rapid moves and some jogging with the handwheel. I was afraid to run it to long thinking it might mess up the drive. Do you have documentation on how to...
Have you done any of this type of tuning with an oscilloscope? I have a 100mhz 2 channel unit available for use. Using the scope would be more accurate wouldn't it?
How do I do the adjustment with the position error diagnostic? Will this be a number that is constantly moving and I am trying to settle the movement? Or am I trying for a certain number in the...
I have a Kiwa Excel center-4 with the 3m-c control. I had to replace the z axis dc servo motor model A06B-0642-B011. After replacing the motor the movement is ok but the motor is making a squealing...
Hello everyone, I am looking for someone with this machine and control for tool changer help. I had to delete all programs and now my tool changer doesn't work. I'm not sure if the machine uses...
Hello everyone, I am looking for someone with this machine and control for tool changer help. I had to delete all programs and now my tool changer doesn't work. I'm not sure if the machine uses...
Would it work ok to just stick a pin in the back of the connector at spot 29 and use a jumper wire from the pin to ground?
Do I need to remove that wire from the plug and plug it back in then find some way of accessing the pin on the board under the plug to ground it?
When I turn on the PWE switch it does throw a p/s100 alarm on the screen. When I turn it back off and press the ready button it does not dissappear from the screen.
I have tried entering parameters in all the different numbers. I followed the directions in the fanuc maintaince manual exactly. Before the servos shut off I could enter the parameters by simply...
I tried that method. I have the Fanuc maintenance and operators manuals for the control. I have followed the steps to enter parameters exactly and I can't get them to go in the control. I have a...
I'll give all the steps I use. I flip the parameter switch on the motherboard to on. I turn on the machine and hit the ready button on the control. When the screen comes up it shows p/s 100 on the...
I have a 3m model c control and I cant enter parameters in it. I put the e stop on and flip the parameter write switch on and the screen displays the p/s100 alarm as it should. When I go to the...
I'm looking for someone who has a Kiwa Excel center-4 with the Fanuc 3m-c control. I need various pieces of information for the tool changer.
I'm looking for someone out there who has a Kiwa with the Fanuc 3m-c controller. I need help with the tool changer.
I had to delete everything out of my machines memory when changing motherboards.I didn't know how to unlock the hidden programs for the changer when I punched all the programs out. Now I am missing...
I have a Fanuc 3m model c from 1984 on my mill. The mill is a kiwa excel center-4. I put a replacement motherboard on it because it had a watchdog alarm. I connected everything up just as the...
I have a kiwa with the 3m control and I had a very similar problem. One day out of the blue the tool carousel would just go round and round and never stop. I found that the board that the tool...
Was there a positive answer of what was causing this z encoder cable error. I have the same board with the same problem and I need to get it fixed.
Try one of this number.
Memex Inc.
Burlington, On L7n 3v6 canada
905-635-1540
Ask for
Wayne McPhail.