Search:

2006 Haas TM2. I have been trying to transfer my parameters to floppy. This is the procedure that I was told to use:

Put floppy in drive.
Push "List Prog" button.
Push "Param/Diag" button.
Type...

Is there any way to figure what is making the noise short of disconnecting the ball screw. I figure if I disconnect the ball screw the control will not allow me to rapid that axis making it harder to...

Good point and yes it does still hold tolerance. I may sell the machine though. I figure if I can fix it reasonably cheap I can get more $ for it

I replaced the processor board on my '06 TM2 it cost ~$3500

I know this is an old thread but just as a arning. When the machine says to replace the backup battery don't postpone too much. I made the mistake of waiting and lost all my stuff that was in memory...

My TM2 sat for a bit with being run over the Summer. Y axis makes noise now when running at rapid traverse. I'm thinking its probably the ball screw or linear bearing. Ball scrw I think would be...

I figure I should update this. I called Haas service. They had never heard of something like this happening. One suggestion was to initialize the machine. I decided before trying that I would put a...

I woke up in the middle of the night with the exact thought. I wonder if I can replace the key board myself.

Hmm 71 views no replies. This isn't good. I took the ccover off the back of the control. Placed a lamp with an incandescent bulb inside. Waited an hour or 2. Started the machine. I worked fine. I...

My 2006 Haas TM2 won't let me edit programs. It doesn't give me an error. I load a program, hit Edit, program shows up screen for a fraction of a second , then control goes to MDI screen. I checked...

Battery went dead on our Bridgeport EZ Trac

ITs hard to believe but the battery is soldered in. We checked locally for someone that could replace the battery but there place we took it...

I was using HArdinge DV59 lathe the other day. When I shift the High/Low speed lever from High to neutral it makes a clunking sound. I have never heard this before . Any Idea what would cause...

Hi Can someone tell me how a chuck mounts on a Hardinge DV 59. Is it threaded or a tapered nose like the HLVH?

It was my HFO. The same place I purchased the machine

Had one. $5000 later :devious: He had to replace the processor board. In the beginning I was told it might be the processor board. Cost of $400 to $1600 for the board plus install & travel & what...

Help Haas TM2 won't boot I have a problem with my Haas TM2. When I turn it on this is what I get:

Copyright 2005 Haas Automation

Initializing control...
Zero...

Thanks. I only owe the bank not Hass. My Haas dealer must be wondering though. I have had the machine for just over a year and I finally have to get this code.

OK today I started up my TM2. After it did it resatrt it showed this message on the screen. Paraphrase

"You have 100 hrs raemaining. Please call your Hass dealer to get some sort of code."
...

I have a Haas TM-2. I needed to cut a pocket so I used the ISP mode ( I think thats what the mode is called). From the hand jog mode I scrolled over to pocket milling then to rectangular. I put in...

Is Esprit the same software that came with my Haas machine?

I bought a TM2 this past Oct. I agree its a messy machine. I made some plastic covers that really helped with the coolant splatter. All in all I love the machine and would gladly buy another.

Hmmmm I don't know. I don't remember seeing frame milling in the menu selections either. I'll have to look tomorrow

Why don't they have a Square pocket milling VQC template?

Accordong to my hass manual G150 is for pocket milling. My book doesn't go into alot of detail. Can someone give me a little extra insight onto this g-code? Thanks Tim

I have a pair of stepping motors and drivers. I would like to control movement of the steppers with a simple joystick. Does anyone know where I can find such a thing? Motor & driver info:

I have...

I have a pair of stepping motors and drivers. I would like to control movement of the steppers with a simple joystick. Does anyone know where I can find such a thing? Motor & driver info:

I have...

The USB drive connection is $3,000 without any drive just the USB port. I can't see paying that much. Run an RS232 line and you're cooking with gas!

They have a chip/coolant guard that mounts to the table ($729). I don't know how good it works, I didn't buy it. I do alot of large plates so I figured the guard would be in the way and I didn't...

Matt, I just bought a TM2. I love it. I think getting some of these options greatly depends on your budget. I skipped the USB/floppy drive. I just hook up my notebook computer. Minor hassle with...

I think I'll just have to get used putting the decimal point in. I work metric so 5mm becomes .5mm. PITA but I'll have to get used to it. I would think that there is some sort of parameter or...