Search:

I have lost the parameters for the machine. Does anyone have a copy I could have?

I found the parameter that was off. Machine is running.

Does anyone have parameters for Hitachi Seiki 25S Yasnac LX2 (Yaskawa)? Im getting Alarm Code 173 Memory Error (PRM). I think I might have some parameters scrambled, but I dont have the parameters...

Obviously I have (tool list) in my post, but I also have this Addin turned on "Add stock tool list and setup sheet.bas". I believe I downloaded that Addin a long time ago. Not sure if its still...

You want it to look similar to this?

%
O0001

(126487) (4-30-2015)
(126487 REV 2) (11:02.4)

( ROUND STOCK - INCONEL_718. OD 2 ID 0.9 Z 1.93 )

So your choosing Hole from Dimensions With a Counterbore? Thats the only way I can think of that you can do side milling with Hole from Dimensions, which I never use for side milling. Ive always...

No sir it is not. I found the relay that goes to the Master start, and swapped it out, and that didnt work. I havent had a chance to do anything else with it. I did notice the lights above the...

Anytime I see that screen, Ive had to reload all the parameters. Fortunately, I have a good back. I have 2 machines with the 11M. Happens about every other year or so. If you dont know what your...

In case anyone wanted to know, I figured out the Wear page has to be entered with a U, instead of an X. Geometry X and Wear U.

Yes, but Ive had problems sliding it through before, because its gets built up with gunk near the chuck. Ive had to unbolt the cylinder, and slide it back a little. Theres a lock nut on the draw tube...

269250

Previous owners program used Tools 5 and 6, and Tool 5 and 6 were the only tools loaded in the turret.

Good point, but the wear page has numbers already in it for the tools that were in the turret, and the match the tools called up in the previous owners program. Its pretty obvious the previous owner...

I recently purchased an Excel with a Fanuc OT. Ive worked with a Fanuc OT years ago, so I have a little knowledge with it, but Im still refreshing myself.

Ive set the tool and roughed a part with...

It basically a repeat of designated lines, similar to a finish can cycle. It also work well on a lathe, if you want to run more than one part with a bar puller or a bar feeder.

It creates sub programs so you can reduce the size of the program. Lets say your milling a pocket 5" deep, but your only taking .05" DOC. That would be a lot of lines. Using macros, your program...

Does it do that with all your programs or just this one? If its just this program, than it probably has something to do with you ending with a radius. Mine will do this sometimes when Im programing...

I have the VA45 but with a Fanuc 11M. For mine, in order to move the axis, I have to hold down the red "spindle stop" button, which acts as an override. Sometimes Im able to manually move the arm,...

I have 5 Hitachi Seikis and I love them, but I can understand some of the pains all of you are going through. Im in Houston, so I obviously try and use local techs, but when Im in a bind for parts or...

Do you happen to remember which relay it was?

Figures. Thought I was purchasing a running machine. :mad: Thanks for the response.

Im having the same issue, but I just bought the machine. Hydraulics are on, and chip conveyor will turn on, but thats as far as I can get. No axis movement. No one knows how to reset this alarm?????

I had a tech look at it. He swapped the Ram like you said, ect. He said the HD is fine. The problem is the CPU board. Anyone know where I can get it worked on? I usually use Midwest CNC, but the only...

So it could be a virus, even though Ive never connected the machine to anything? That is the part I dont understand. I could understand if I was downloading to the machine, but I never have. I use...

No idea. Doesnt make sense to me. The hard drive is cheap, but having a tech reload the operating system, ect. wont be. So Im just looking for a 2nd opinion.

When the machine is turned on it gets stuck at "Invalid configuration - please run setup" OR it gets past that and ends up giving a "base memory fault - less than 640k" The power supply is good. A...

All you need is this (TOOL-LIST)<EOB> in your post

Need more info. Are you using a proven post from a previous version or is this a new post? Posting a copy of the NC program would be useful. If you dont have the proper M code in the program, its...

Changing your Material and/or Machining Attributes will change your default settings. If you made any changes while writing the program, those will not change. Youll have to manually change them...

There is a check box for "use finish tool" in your turn and face properties. Make sure its unchecked before tool selection, and it will select the same tool for rough and finish.
...

you should get a competitive upgrade discount for having bobcad