I have a Mitsubishi M700 control on my VMC. I am trying to automate my Tool setting but I cannot find the Variable number for the 'tool in the spindle'. Any help would be appreciated.
At this...
Type: Posts; User: RdHawg
I have a Mitsubishi M700 control on my VMC. I am trying to automate my Tool setting but I cannot find the Variable number for the 'tool in the spindle'. Any help would be appreciated.
At this...
In my DMU70 5ax 840D, I sometimes do work that is longer then the machine x travel and would like to swivel the work 180deg to bring more of it into the work envelope. Unfortunately I've found no...
Where are you physically located? Maybe someone local could help you?
I Had a USB Drive once that did not like the ports on the screen - but worked on the one by the power breaker. The wires on the USB Drive need to extend all the way to the end of the plug to work in...
Anyone know how to get the single block to stop after each hole? The way my system is set now, it wants to stop after each peck.
Thanks
Brian
Before I tossed this in the trash I thought it best to document it here in case someone was searching the world over for it. It is a scan of the original Maintenance and Operations manual 89092...
Is there a way I can change the daylight savings dates? It changes a week or two ahead/behind so my clock is off during those times.
Thanks
I did solve it - after much searching of the machine manuals I was able to find the applicable _OVR Variable list. Thank you for your offer.
Brian
So I wrote this program on the machine (not sure where all the giberish came from but I believe all the values are there)
N1 G17 G40 G64 G90
N2 TRAFOOF
N3 CYCLE800()
N4 ;M90
N5 ;PROBE WEBS
N6...
I thought the G320X brought the encoder signal back to itself?
In other news... The Y servo is the same as the Z But the X Servo is a Baldor:
cat#4203623
28IN/lbs (448 oz - does this mean a...
I have a 3 axis dynapath 10 control bridgeport I'd like to convert to Mach 3. I'm not too sure where to start. I need at least a breakout board and some servo controllers to drive the servos.
...
REMI - Clean out your message box please.
Job awarded to forum member
Part can be 303/304 approx 2.7inch dia 10 mm thick. The groove is simply for glue so close counts. All surfaces need to be machined.
For those that might also be struggling with this. It was suggested by my Hypermill tech guy to change the Cycle832 setting from finish to pre-finish or roughing. Worked great - I think I actually...
Link to to another forum:
DMU70 Siemens 840D 5ax feedrate question - CNCzone.com-The Largest Machinist Community on the net!
Feedrate question on a Siemens control
In 5ax mode with TRAORI and Cycle832 active My feedrate of 90IPM does fine in a straight X/Y/Z move but then slows to a crawl when a B or C move is called out. (Utilizing a bunch of tiny G1/Vector...
Still Looking :wave:
Looking for someone with grinding experience to mfr ceramic parts both green and fired. Also doubles as our tool and cutter grinder. Needs to be able to operate independently.
Great Pay (DOE of...
Is there such a thing in Esprit?
Really Look At hypermill! I've been using esprit for over a year and still struggle to make time on jobs. I used hypermill for 3mos before I started making time on jobs. Esprit has excellent help...
Try these guys - 510-236-7415 / 510-215-8524 Richard Fox, Samuel Perez
3451 Collins Ave Richmond, CA 94806-2000
I called about some castable refratory and they seemed to have decent pricing....
Is the ball screw still attached to the step motor? As the stepper's braking action would hold it in place? (Just random mussing)
If you use the 'q' it will peck tap!
My #1201 Has ZPR over bit 7? Same thing? Where could I double check that before I do something tragic?!
Because sometimes I restart a program in the middle of it and the controller never reads the line with the offset in it. (Not good)
On a Fanuc 160is-m control is there an easy way to change the default work offset?
Ie. right now when I hit the reset key the controller always goes to G54 - I would like to be able to change that...
I didn't even know that was an option! I have a stand alone (Hypercad) seat
Dragging this back up because I have recently acquired one of these myself. I checked on the japan servo site as best I could and came up empty. Info anyone?
Here's a good jumping off point.. intro to Rapid_prototyping
One really nice benefit to rapid prototyping your parts is that if nested properly you could theoreticly produce one entire assembly's...