Henrik, Good day,
What is status on UHU servo module? I am looking at old post . Is there web site to purchase from?
Regards,
Don in USA PA
Type: Posts; User: gm276
Henrik, Good day,
What is status on UHU servo module? I am looking at old post . Is there web site to purchase from?
Regards,
Don in USA PA
Malaxis,
I have several PV2 amps and no manual. I am particularly stuck on 26 pin CN1 for host input.
Would you have a diagram?
Thanks Don B
A better day today. Got the servo drives in the green !
Wired a non MUMS motor except for the RX (since this motor has none) then I pumped in the output of a real mums motor to the RX on the...
Jon,
No, starting to think the drives are bad. ERROR 22
I am waiting for some connectors but I did hook up the output of the rx leads from the mums motor and still the error persisted.
I will...
Jon,
I managed to get my own mums motor. So all of the above was from observation of the rx leads.
Don B
Jon, I think I have it.
After a bit of head scratching and some time with the scope.
bits 1 2 and 3 are the hall states. bits 4 5 and 6 are the complements of the hall state but in reverse...
ended up making my own.
routed two pcbs like edge connectors. 1.27mm pitch.
put one on each side of op connector. soldered leads on to pcbs.
seems like it works fine.
Don B
I am trying to find the pc software to communicate with Sanyo Denki PV 2 drives.
I tried to use the software for PY drives but it just gave a wrong version message.
Any clues?
Regards,
Don B...
Charles, I have Sanyo Denki PV 2 drives. I made a cable and tried the PY - PC software but I get a wrong version message.
Do you know where I can get the PC - to - PV 2 software? Best...
Jon,
I would love to know what the MUMS puts out. I wonder what the differential voltage needs to be (now putting out 0 volt and 5 volt). Parity or not. Least significant bit sent first?
Inter...
I hooked up a usb converter that can do 1M serial. Sent the output to a 75als191 differential driver and tried to feed the REC leads on the panasonic drive. . still get encoder error.
Out of ideas. ...
Any one know where to buy a connector for Sanyo denki servo OP connector.
It is some kind of 20 pin dual inline.
THX Don B in PA
Hoping to find a MUMS Panasonic servo motor. I am trying to test some servo drives that require
the signal from that motor. Can be damaged physically.
Thanks
Don B in PA
Jon, I seem to be in the reverse situation. I have three panasonic MUDS drives but no matching MUMS motors. I read the previous post with interest as I attempted to gather any info I could on ...
223268
Anyone know the name of this collet type. It measures like an ER-25 but note the three indents on the face of the
collet nut. It is set up with limited turn of the collet nut.
Regards, ...
I had the same problem. since the RS232 connection uses the
3 pins across the center of the DIN connector, I just used
3 pieces of solid wire (cut off of some resistors). I pushed
the wires thru...
I found that milleditpost stopped working when I loaded the latest
update. I also noticed that although there is a bobcadpost directory,
nothing was in it. I made a copy of all the post files I...
Using Bobcad V22 and cannot get the millpostedit.exe to run.
I either an error msg or else if I have it point to a different
directory for the posts, it will run but will not load any files to...
JR
Wow, I did not really notice how old the original post was.
Anyway thanks for the info. I have an extra screw nut I'll
hang on to then. I did replace the bearings from the solid
"plastic"...
Julio,
That's a nice slide. I recently built my CNC out of the same unit. I used it for the Y axis. I removed the coils, magnet and encoder and substituted a pulley
driven by an external...