Search:

Hello,

We have a Vista Sentry mold injection machine model: VSX85 3.51 that is slamming the plattens when openning and closing. The machine is not controlling the speed of the platen movement at...

Hello John,

I have not been able to try your las suggestion yet. I've had other higher priorities with a couple of other machines & I was out of the plant yesturday.
This morning it turned out...

We'll try this out...... Thanks,

We have not attempted to adjust any parameters that would affect this particular issue. We only had to adjust parameter #105 "workpiece coordinate system x movement" -- We adjusted this one because...

Thanks John,

We did not lose the programs on this machin, but we did lose the parameters. We have manually restored the parameters. We have them backed up on a printout and we restored them one...

Hello,
Does anyone know how to recover from the following alarms on a Seiki-Seicos LII on a HITEC-TURN 15-SRL machine MICON 16-II. I have the following alarms appearing on my screen 104: bubble...

all parameters are back the way they were befoe we went into the macine to try and solve the problem. What is happening is that I am getting alarms 310,320,330 axis need zeroing. We zero out the...

All parameters are back to the way they were. Tried P + CAN during power up and released untill machine completely boot up. Tried Zeroing Z axis and got HARD overtravel alarm. Tried with the other...

Thanks...... Will try it.

sshhh... ok.

This machine does have zero return P.B. for each of the axis. When we do a zero return for any of the axis, they end up overtraveling. We thought maybe parameters were screwed up. ...

I HAVE A FEW ALARMS ON A FANUC MF-N4 (FANUC OMC) CONTROL ON A MORI SEIKI M300 PARTNER MACHINE. DOES ANYONE HAVE A PROCEDURE FOR RESETING THESE ALARMS FOR THIS PARTICULAR CONTROL?

THANKS, I'LL MAKE SURE WE TAKE A LOOK AT THAT POTENTIAL CAUSE AS WELL BEFORE CONSIDERING REPLACEMENT OF THIS POWER SUPPLY.

Thanks for the tip. We are beginning to suspect that our problem does originate in the power supply unit. When we disconnect the CP31 on the power supply unit comming from the input unit, the red...

HELLO, I HAVE AN OKUMA & HOWA ACT2SP-3 WITH A FAUNUC 6T CONTROLLER THAT HAS BEEN SHUTTING DOWN ON US DURING OPERATION. THIS MACHINE'S OPERATOR STATION AND HYDRAULICS WILL SHUT DOWN INTERMITENTLY...

Thanks,
We had been concentrating on the 4th axis clamp/unclamp switches. We adjusted one of the switches but it turned out not to be the problem once we adjusted it. (the switches needed...

I have an OKK HM500S with a FANUC 300is Series control that will not allow any axis movement or zeroing out of axis'. This after the machine suffered a crash. The spindle tool was crashed into the...

Thanks MEMORYMAN,

We checked out the BMU board on our machine. We were going run the initialize procedure for this board, but found that we had two other BMU boards removed from a machine we used...

OTHER OBSERVATIONS ON 6t LOCK-UP PROBLEM:

1- If the machine mode select switch is set to ZERO POS for zeroing function, and the hydraulic system is turned on, both side A and B can be zeroed out...

OBSERVATIONS ON FURTHER TROUBLESHOOTING OF 6t LOCK-UP PROBLEM

When the machine is turned on and the mode selector switch is set to EDIT on the B side of the machine, all of the following functions...

Thanks for your input....

We originally suspected the power supply and installed a new one. After installing a new power supply, we replaced the input unit as well, but the problem continues. ...

Hello..

I have a problem with a FANUC SYSTEM 6t control Series 44 versioin .05.
This control is on an Okuma & Howa 2SP machine. This machine has two posts, A and B side. The A side is working...