Smdh, that worked..well over 40hrs messing with it.
Thanks!
Type: Posts; User: repauli1
Smdh, that worked..well over 40hrs messing with it.
Thanks!
I have a large router, fighting issues with overcurrent faults when cycling power.
On a cold start it always starts up fine, but if I cycle power to drives, when Oak and drives come back up, usally...
Did you fix the issue? If so what was the root cause? I am having DMM faulting on power cycle issues.
I just run the individual tool programs for the op I am doing, that way it compensated for wear.
If your good at programming you can modify one to do a loop until you have measured your last tool....
I realize this post is four years old, do you still service these boards?
Thanks Bob
Where do you enter the probe tip diameter settings?
I have gone thru all parameters cannot find it.
This is an older haas..
Don't know where you are located, but Andrew is 9hrs difference from Illinois. I would suggest you work with him thru Telegram and TeamViewer versus emails. He seems to be avaiable around 5AM-8AM CST...
How did you calibrate your probe offsets in 59-63? I cannot get the haas 9999 calibrate to function correctly on my old 1997 machine.
BTW Your dropbox programs are GREAT! Thanks!
Thanks
Any progress reports?
After I moved my VFE-0 MILL to my home shop I have been having an issue.
When the spindle starts with a speed command of 7500rpm, the motor load goes to 100% and stays there for 5-10seconds with...
A work around I put a G4 P2500 right after the G54 move (Dwell 2500ms)
I know how to change it, just cannot find that parameter on my list under 209
Thanks for the response, I cannot find that parameter even though its in my book, I am on the 209 par page also???
Vintage 1998 HAAS
When my tool holder grabs a tool and the spindle starts, there is a delay when set at any speeds above 2000 rpm, if I am doing an aggressive adaptive clearing I have to FEED HOLD...
When it says Machine is not powered, one of the axes is probably sitting on limit switch, to apply power to move off limit follow the below instructions.
Hopefully I saved some newbie like me to...
I got the unbrella to go to park by disconnecting air hose, and swinging it back. I am pretty confident that my Z is at it's upper limit position, preventing the contactors from staying powered, is...
Mine is driven by a pneumatic piston I believe. (THE SWING MOTION)
No nothing moves, and it says machine is not powered
New to machine, I hit the tool charger button without z being all the way up. Unbrella hit bottom of single, I raised up to top, but then restarted machine
I have a 1997 Arrow 500, the umbrella is in the spindle position, and when trying to start up the mill, the relays pull in but release within a couple seconds, with the main machine stating "machine...
[QUOTE=kenrbass;2325352]Is that the one from Dallas? It just looked like it took up to much room for me. It looks solid.[/QUOTE
No, I knew the guy, I bought three Cincinnati Arrow mills from him...
Just bought this old router, really nothing to be found googling it. Paid 3k for it, it runs well, drip feeding code. 2 zone vacuum table.
Needing a vacuum pump, blower, any suggests. Also feedback...
Check out Teknic Clearpath, they are servos, with built in drive, three wire to step/directly, and two to power. Powerful also!
I have a 1997 HAAS VF-E if you need any tips just let me know. I set all my tool's offset to the Table, then I just measure the top of work piece, and subtract from table top, enter value as a...
I lost about a pint of hydro oil while fighting my valve. How did you refill the oil?
If anyone is considering converting their BP to CNC, send me a message. I converted mine and it works great! Now designing a flood coolant tray for it.
Well 8yrs later how do you like it, Ordered mine today...
I just got my CANDCNC up & running, surprised at how well it functions!
I have it on a homemade plasma table, currently using my Hypertherm30 with a DP-03 on it, but I just bought a Hypertherm65, so...
Did you do a new install of Mach3?
Power driver OFF first