Found the answer, digital input (DGT-IN1) enables the drive, DGT-IN2 enables motion commands, enable one then the second and away it will go.
Page 40 of rev.2/02/2005 in the manual
Type: Posts; User: jrslick22
Found the answer, digital input (DGT-IN1) enables the drive, DGT-IN2 enables motion commands, enable one then the second and away it will go.
Page 40 of rev.2/02/2005 in the manual
I'm working on an old machine that uses the Magnum 400 drive amplifiers and need a bit of help getting it to work.
Everything works on the drives, I can jog the servos using the "digital speed"...
Ive use with good success xhc's motion cards, here is a like for a pdf
...
the dude who did the work for me did it on the condition that I protected his I.P. happy to point people in the right direction tho
Ive pretty much solved this by having a homing routine then having a macro running to enable disable the output given on the x and y position.
Im not sure this will solve the problem, when i do things like rip cut the vents wont open? If i understand correctly
Sent from my SM-G920I using Tapatalk
I have built my down draft table on my plasma with air rams to open and close each section of the table so i can direct the suction to the area the torch is working in, i would like to automate this...
UB1 installed in cabinet with the front over off, looks even better with the cover on.
376502
Im building one at the moment, uccnc, neuron thc, hypertherm.
374644
same here, would love to get this working on uccnc
Is this still the best firmware for disabling error recovery mode?
Can someone please link me to/tell me how to upgrade the firmware?
cheers
Hey GD. I've made good progress thus far, I have my belt drive set up just like yours, I getting about 8k just like yours, hell I even packed my bearings in kuLuber grease today just like yours! I'm...
I was more thinking a key for powder coating.
Does this work on any surface or only galv? im looing to prep Ali, what version of vinegar is best?
thx
Hi JD, would you mind giving me the code for the belt you are using on your spindle belt drive conversion, im esp after the langth? thx
Yes they have said that, as long it is not for general consumption there will be limited or no development.
Such a shame.
I have run my Grex from the Internet! My machine was having issues, i have been to work 0n the other side of town and used the PC at work running mach3 to connect to my house and test my Grex, worked...
Very smart, well done.
I brought two Grex's when they first came out an loved them, i found out that Gecko have stopped selling them due to the difficulty of setting them up. all of that firmware IP address information can...
Just wondering if there is someway once the motors are disabled that i can hand wind the DRO's
thanks.
Mach3 by artsoft is a good place to start.
You can get started straight away by using software backlash compensation, it wont be super accurate but it will give you some time to save up and replace your screws and nuts with precision ground...
Am also looking at one of the machineryhouse lathes so would also like feedback from anyone who owns one.
Ideas anyone
Yes Steve V21 is correct
When you talk about turning it off under bobcad, under the NC in bobcan i have selected no comp under contour. i'm not sure where else to switch it off.
thanks.
So i basically understand about 20% of what is being said.
Im not 100% clear about cutter comp or D offset, i know it has something to do with moving the tool in relation to the tool path, please...
I found this post http://www.machsupport.com/forum/index.php/topic,3820.0.html and have recreated the code using it, so far i have not produced the junk.
I would have thought that a decent post...
The reason i suggested it was the post.p was because my mill has and does run perfectly.
Mach in my opinion is a great product, the PC its running has also been problem free and versatile. will DSP...
Im using the Post called Mach of the artsoft website along with the scrips that are also provided as part of the download. is there a newer ver. than this?
machine is at the workshop so i can try...
Can someone please help me figure out what is going on with my Gcode, when i run a simulation under bobcad it looks perfect, when i import the code into Mach3 it looks mental. (the not blue part)...