Yes, the mini machine torch will work with the Powermax45 and the Powermax45xp. Use the cut charts from the Powermax45xp operators manual which you can download for free at Hypertherm.com Jim Colt
Type: Posts; User: jimcolt
Yes, the mini machine torch will work with the Powermax45 and the Powermax45xp. Use the cut charts from the Powermax45xp operators manual which you can download for free at Hypertherm.com Jim Colt
What brand and model cnc plasma table? The arc voltage that can be measured inside the Powermax1000 is used as feedback for your cnc machine or height control to control torch to work distance. To...
There are a number of lower cost consumables that are poor copies of a Genuine Hypertherm consumables. These are illegal , patent infringing parts and are built using incorrect alloys, with poor...
The attached wiring diagram is when a Powermax45xp, 65, 85, 105 or 125 equipped with a machine torch will interface to a PlasmaCam table. If a plasmacam table is equipped with a hand torch, then you...
Unplug the machine torch, plug in the hand torch. Connect the work clamp to what you need to cut, start cutting. When the machine torch is plugged in it will only fire from a signal through the rear...
Best bet is to either work with your machine supplier (OEM that built and sold you your machine) or contact Hypertherm technical service. They will help you quickly solve the issue. Be sure you have...
TomNJ,
Shield technology (originally developed by Hypertherm in the 1980's) with Hypertherm's air plasma systems has the following technical benefits:
- Does not allow the nozzle to contact the...
First, be sure you have genuine consumables. There are a lot of copies of the consumables as well as the packaging. If you bought from an authorized Hypertherm dealer then you are likely ok. Second,...
Here is a .pdf file of a note I had sent to another user with the same question. Keep in mind that the Plasmacam interface cable has a red and black pair. The red needs to connect to negative...
1. Ohmic contact (Plasma) uses the front most metal component of a shielded plasma torch to locate the surface of the material being cut. This process puts very little downward pressure on the...
I would suggest looking carefully at the machine code used for that particular cut file. The plasma cutter amperage or choice of consumables should have no impact on the motion.....so that part does...
First, their is no part called a tip in a Hypertherm torch. The electrode is negative output from the power supply, the nozzle is positive during pilot arc (arc start/transfer to material) and the...
Sounds like a loose connection or a failing voltage divider or THC. You can verify the real output voltage with any plasma cutter by reading it with a voltmeter on the DC voltage scale, on a 300 volt...
Yes, go to www.hypertherm.com , at the bottom of the page find the downloads library tab and click it. Choose HPR130xd in the drop down menu, then find the operators manual and download it. There is...
Your first place for help is with the OEM machine builder. If they need help, they should contact their Hypertherm sales representative or technical service at Hypertherm. Should be easy to fix. Jim...
Contact your cnc machine builder, if they cannot help then ask them to work directly with Hypertherm tech service for your region. Jim Colt Hyperthermn
Tracker cnc, Fab-Cut CNC, FastcutCNC and Machitech are all great Canadian cnc plasma machine manufacturers and can all provide products that will achive the cuts that you need witin your budget. ...
Open your Powermax operators manual to the mechanized cut charts. Listed there are the correct consumables for machine torch cutting, as well as the cutting specs (pierce height, pierce delay, cut...
That entirely depends on what plasma cutter you intend to use. Let me know and I may be able to help! Jim Colt
What CNC machine, cnc control, software? Water table or downdraft? The plasma does not do the hole cutting by itself, rather it requires well coordinated motion involving the x-y drives, z axis...
The Powermax45XP outsells the Miller Spectrum 625, so it is competitive. The higher wattage output of the 45XP (due to higher cutting load voltage) makes it more powerful, but also makes it not able...
The Powermax45xp is 230 volts, it is the lowest powered plasma that we recommend for cnc use. The Powermax30 is used by some people on cnc machines as long as you keep the duty cycle low and stay...
You probably could put a quick disconnect on a 30, though I have never done this.....so I cannot offer advice. Keep in mind that there is the possibility of open circuit DC voltage of around 300,...
Slowing the cut speed is the worse thing you can do. For 6mm steel you should use the 45 amp shielded cutting process and follow the book specs from the operators manual exactly....generally the cuts...
The last one that I opened that was clearly sealed from the factory in the USA had a manual (as well as the safety and compliance manual that we are required by CSA and CE to include). As soon as I...
paulomacc,
I have no idea what we (Hypertherm) are supplying for printed manuals currently. I will forward your message to our Powermax team and as soon as I get a reply I will respond. You can...
The switch does not see both situations. It will send too loose or stack up tolerance issues ( common with aftermarket consumables) if the cap is over tightened it can cause the electrode to bind (...
I sent this response yesterday, apparently it did not get to you. Best way to communicate with me is through [email protected] . Best place for Hypertherm tech issues is...
The HyAmp torch will work fine on the 65....a bit better consumable life as it has better cooling. The torch diameter is larger, and be sure to use the Hyamp cut charts. Jim Colt Hypertherm
Hypertherm generally recommends its plasma cutters that are available with machine torches and with output amperage of 45 amps or higher for CNC cutting machine use. There are a number of people...