Search:

Were do I find APZ setting?

Axis 3 is the turret tool position.
By reference point do you mean the home position.
Do you know the parameter to turn off the tool setter as it maybe causing the issue and if we can tell the...

If I change 1320 Z to 99999999 as you suggested before I can move right to home on the Z axis but if I leave it at the current setting it just errors with out moving at all. Attached are the images...

The machine has a inbuilt tool setter and the points that don't work relay to the same as the axis that don't drive in.

505086

505088

When I use 1320 at 99999999 it allows me to travel to the home but I can't move back. When I put 1320 back to 5000 (what it was) and wind the ball screw back by hand with the power off. Power up...

I tried that and it still didn't let me move in the -Z, I also can't move the X in the home direction. I have checked the drives and it doesn't show any error. Seems the Z & X will only go in one...

I have wound the screw back manually but it doesn't make any difference.
.I wonder if the position encoder is showing the incorrect number on start up and assumes its to far.

Hi,
I can't home the X or Z.
Attempt to home the Z come up with a error "500 over travel in the +Z". It fails to move to or away from home.
The X will move away from home but not to home.
Any...

We have a Mill fitted with Proto Trak SMX controls. On start up it some times goes into demo mode. My question is does anyone know what causes it to go into demo mode then maybe we can fix it.

The guy that did the Linux is the guy that let me don't and has my books.
Each axis has its own drive and a Sayno Denki motor, its only the spindle that is Fanuc. Give how cheap Servo motors have...

Hi all,
I have a Hitachi Seiki VM40 and I want to redo the electronics, so the plan is to replace X, Y & Z drive motors and drives and only keep the current spindle and spindle drive which are...

Got to say I am impressed Tormach came back to me with a number of answers to my problems, very efficient. Its a great company with a great product.
I am asking a lot from the software we want to...

I have recently purchased the Tormach CNC Scanner V2 package,
Once I got the my head around the workings of the software it has worked out well and will be a great asset to my business. I have a...

We have news,
Spoke to Fanuc guys today and it seems the error 414 I was getting was from a OVC showing on fault screen 200. Check the turret zero position and I found that it was 9mm out of line,...

Okay just tried it and still get the same error did the reset on 1815 as suggested.

Do I have the Keep relays set K13.0, K13.1 & k13.2 relays set at Zero when I do the changes on 1815?

Okay I will give it a go, also I think the fact that I have a 56mm dia Udrill maybe throwing the balance out as well so I will remove that ans see if there is a difference. I am in Australia so I...

I must be missing somthing,
In the good book (actual its a bad book because its making me more confused) it doesn't mention APC changes at all.
So it says go into 1815 APZ and change to 0, turn...

I have a Takisawa TC20 and I did a grid shift on "3" then I got the 300 APC: 3 AXIS NEED ZRN error. Had a lot of drama understanding the manual so my have stuffed up something but now after after...

Hi Bob,
I just brought one of these machines how is your mods going? Have you finished the project yet? Tried to send a message but your mail box is full.
Tony

HI John,
Sorry for the late reply I have been keep busy on other things. In answer to your question the machine I brought had ball screws on the x and Y, it was Prototract ready from Standco. ...

Ford,
Yes its the turret servo and its "3", I have been playing around with "Grid Shift" in the parmeters. I am waiting for a dail guage to arrive but it seems that I can raise or lower the turret...

I am not sure if its called "3" instead of Y, it seems the angle of the boring bar tip is not contacting the surface at the correct angle and it shuddering. I will have a look at G54, thanks. In...

How do I adjust the Y axis, it seems the tool is to high by aproxx .6mm. Is there a parmeter for it.
Tony

Did the adjustments to the parameter settings and now its all great. It would be good if some one can tell me the correct way to set the do the set up on the tool setting arm.
Tony

Hi fordav11,
Set the tool at a 40mm wide job "X position" read 71.874,
Used tool setting arm X showed in tool table as 33.029 and the "X Position" as 171.055
Checked Parmeters,
5015 190552...

Hi Guys,
Set all the tools okay but I find the turning tool and the drills are 1.7mm out. In other words if I set "Tool 1" (its a outside turning tool) to be correct then all the tools that rely on...

Hi Recordhound,
Is your the same type, the code seems to make sense as it appears to be the same as the bit I still have.
Thank you very much.
Tony

fordav11



That makes a lot of sense, the guy will bw here in 4 days and I will come back to you on what he says is the problem.
Thanks for the help its much appricated.
Tony

txcncman,
I apolize for the fact that I don't understand what you are saying but I do speak English. I have dyslexia which in case you don't know means I have difficulity reading, writing and...