Here is a schematic CNCRoom published on it's site to connect a Huanyang VFD to a ESS/MB3.
489088
Somehow, I have to get this running by tomorrow afternoon as their production schedule demands...
Type: Posts; User: jlmccuan
Here is a schematic CNCRoom published on it's site to connect a Huanyang VFD to a ESS/MB3.
489088
Somehow, I have to get this running by tomorrow afternoon as their production schedule demands...
From the MB3 Manual and how I set up the last 4 machines I converted.
"New! “AnaSpeed2”is a 0-10V precise analog output circuit has been implemented. This small circuit island is electrical...
In my other conversions, the ESS and MB3 boards are set up before connecting the VFD to confirm the AG/AO circuit is configured correctly in Mach. Once I get the correct voltages I connect the VFD...
Setup - ESS, MB3, Mach3 R3.043.062
I have configured Mach3 and when I issue an M3 with a speed the LED for the analog signal on the MB3 lights up. Slower speed, dimmer light. Higher speed brighter...
I am at a client's shop in Florida and we have a dead MB3 board. We thought it was only the Smoothstepper, but it turns out to be the MB3 as well. Where can we get the MB3 board by Monday or Tuesday?...
As stated above, my relay board turns on all NO connections when power is supplied to the load. I've put a 10 second delay on the power to the board but it seems to be coming from the load side. ...
The spindle orientation not working is because I'm using a VFD and need to add a position indicator. I already have a profile set up in the VFD to run reversed at 30 rpm for tool height and diameter...
I have a 5 HP, 8000rpm spindle in my BT40 machine. I currently don't have my spindle orientation working yet. What do you think about light machining without the drive lugs so that I can use my...
Weird!! I had previously changed to all possible configurations for the Active High and Active Low in the motor outputs. Anything but an Active High on Step and Active Low on Direction, and the...
Good question on the jumpers. I don't have the manual or even a model number for the motor. I do know it is a Mitsubishi 3.7KW. I can run it forward and reverse. The only thing that's not working...
I realize that GCode doesn't recognize the comma. Active High and Active Low changes result in the spindle not coming on at all and wouldn't reverse the analog out signal, only how it is recognized...
Well, I finally got the AO to change voltages, but now the voltages are reversed. With an S10,000 I get a voltage of 1.23 and with an S10 I get a voltage of 9.25. Crazy. There has to be something...
I appreciate the help, but I don't see anything under your post. I also am not familiar with a "Spindle" pin on the MB3. Am I not doing something?
What signal should the spindle be mapped to? I currently have it mapped to the AO pin. Port 3 Pin 17
I have the PWM in Mach3 and the MB3/ESS plugin. Going up or down makes no difference
Well, now I have voltage on the AO by setting the spindle to pin 17 of port 3, but all I can get is 9.5 to 10.5 by changing the potentiometer. Changing the rpm with the S word doesn't change the...
I am using the titled parts but cannot get voltage on the A0 AG connection. I've tried setting the Base Freq all the way to 1000, but it doesn't work. What tells Mach that the MB3 board needs to...
Thought I'd include a followup conclusion for this thread for others with similar problems.
After weighing my options and realizing there was virtually no market interest in an untested...
I though of disabling all the drives but wonder how much position I would lose and if the DRO's would be correct. I quess the simple out would to be to attach it to an alarm that sounds when the...
I assumed it was an AC Servo because the drive is an AC Servo Drive. Maybe I got lucky and it will run. Now what type of VFD would you recommend to get the torque control and hopefully the ability...
I have my door interlocks all sorted out. Now what to do with them. I hate to wire them to the EStop with all that entails in restarting the program. Is there a way just to pause everything until...
I have the above VFD but no manual. Does anyone have a link to the appropriate manual? I hate to buy a new VFD just to get the correct manual. Here is a link to the VFD on Ebay
Jim
I finally got tired of wondering and hooked up a VFD to the power leads to the AC Servo motor. It runs and the VFD changes the speeds. I haven't put a load on it to see if it has torque. Any...
Thanks. Craig. I have 240VAC 3 phase for the spindle motor and Z axis motor. I thought about running a VFD rated motor as I can use a pin for tool change orientation and have wondered about their...
I am looking for a new or lightly used/rebuilt spindle motor for my VMC. It is for a belt drive spindle. I would go for a VFD rated motor or AC servo and drive that would interface with Mach3. I...
What is the base rpm of the motor you have. I may be looking for what you have.
OK. I've decided to ditch the Mitsubishi motor and drive. Now what? Where can I get a comparable or step up in performance, say 8-10000 rpm and 5 to 8 HP with a drive to run it under Mach3? This...
The data plate on this motor is gone and there is no place where it looks like it may have been. All I have are the manuals. Cost is a relative term. For some $4000 is a bargain for others it is...
Thanks, Jim.
Unless we can find a way to run this with a VFD our options are very limited. I doubt I could sell the motor and drive very quickly and we've put in a lot of work to get this machine...
I misprinted the drive. It should be an MDS-SVJ2-37. I've looked at so many manuals, I'm beginning to go blind. You may be correct that the analog is an output.
I'm open to other suggestions,...