Find a 110 power source in the cabinet, run the red to one side of pump, the other wire from pump to n.o on spare m code relay, run white side of power source to common. I have air solenoids that...
Type: Posts; User: djr76
Find a 110 power source in the cabinet, run the red to one side of pump, the other wire from pump to n.o on spare m code relay, run white side of power source to common. I have air solenoids that...
Ive never used GWizard, but my guess with the slider turning from green to yellow means youre pushing the tool outside optimal cutting conditions. I use this calc micro100.hsmadvisor dot com, you...
Are these values for dynamic milling (high efficiency) with chip thinning in mind? HSMadvisor spit out these numbers for 6061 at 1.5" depth, 3/4 carbide. 10k rpm 1962 sfm, 280 ipm. I think Bobs...
The tool path can get quite jerky when going at a high feed rate without having that look ahead feature turned on. I've never used Fusion but in Mastercam, you can mitigate that issue somewhat with...
I plumbed air into the coolant supply line after the ball valve and use the spare M code relays to wire in a solenoid valve. So when I want to use air, I close the ball valve so it doesn't back feed...
Look into broaching.
You could be getting jaw lift if its a cheap vise, or you're clamping above the jaw plate line (taller jaws than the jaw plate) which can cause jaw lift as well. Using a torque wrench to get...
You can always have your metal supplier quote your stock with saw cutting, typically it doesn't cost much for an value added service like that.
I would go with the enclosed tormach over a knee mill. Have you looked into a used haas?
I program with comp on and just adjust the tool size.
Did you call your HFO? Typically they setup and calibrate the probe on installs. I bought a VF8 that was preinstalled and calibrated at the factory.
By Studying the Renishaw Inspection + manual, an add on to Mastercam, or Renishaw has a number of software to generate and export data.
I would google Haas Australia and call the closet hfo near you and talk with tech support.
VF0 26X14
VF1 26X14
VF2 36X14
You can find all the specs at haascnc
Haas Automation Ltd - Headquarters - Norwich
Haas Automation Ltd
Convent Road
Norwich
NR2 1PA
Telephone: 01603 760539
Fax: 01603 760542
Email Sales: [email protected]
Email Service:...
You mean this --------> /
add it in front to what ever block you want to skip.
or if you want to skip a bunch of blocks
/M99 P100
Blocks you want to skip
Try McMaster Carr and type in "water filters" in the search field.
You can room temp black oxide 65-85F. Your vendor should be able to confirm whether or not it will warp though.
Scientific Cutting tools, Inc, has a thread mill G code generator.
I would fight Haas and HFO tooth and nail over this, coolant shouldnt be mixing with grease.
I machine 303 all the time. Just straighten it in an arbor press.
Does it only do it with the one program "B" and no others if "A' is running? If so, have you tried renaming the program(s)?
Is your depth of cut greater than the radius of the insert tip? Did you try pushing your feed rate harder?
in mdi, hit erase program to delete whats stored there.
Set the Insert that is cutting the bore into another tool offset. Then call the tool with corresponding offset you set the tool to in the program.
OSG Hypro NRT list 14001. I just did a job thread forming 10-24 X 1" deep in aluminum, did 3000 holes with 1 tap.
$495.00 in the Haas parts store.
Macro #599 or I think #10599 NGC
Carbide or heavy metal bore bar? What kind of bushing, split, slotted? Does your machine have variable spindle speed? If you have facebook, the group called "Machinist" with 112K members have a...
Did you try browsing the denford website? Specialists in Technology for Education - Denford Ltd