sounds like you need a solenoid if you pay $500 like metalman your getting the whole assembly with the manifold you do not need you can usually get mac and sprecher valves and or coils to replace...
Type: Posts; User: serviceman
sounds like you need a solenoid if you pay $500 like metalman your getting the whole assembly with the manifold you do not need you can usually get mac and sprecher valves and or coils to replace...
93-0153a used to be the fan replacement kit for the vector drives not on the new ones though. not sure if they took it off the market its for the older vector drives with the 2 fans on top.
Reytech Machine Service Corp. www.reytechmachine.com
Repairing Haas Machine Tools in the Ny and NJ area.
Over 15 years experience repairing Haas Machine Tools and others.
Now carries a large...
when you loosen the collar on the motor end you have to turn z ch only on in par 43 then zero return the a when the invis axis is a 0 you only use invis axis to move the turret then clamp and turn it...
2 shirts $8 bucks 2 hats $10 bucks Poster $2 bucks happy customer priceless. you should shoot for nascar tickets, they give them away too.
if you do not have a termination plug for the side of the electrical cabinet then just leave the pallet changer plugged in, it does not have to be lined up as long as you don't try to do a pallet...
Reytech Machine Service Corp. is now an authorized Methods Machine Tool Service company for fanuc robodrills.
QUALITY CNC MACHINE TOOL REPAIR
20 YEARS ELECTRO-MECHANICAL EXPERIENCE
...
anytime, oh there is a pressure switch behind the tank and there is a float switch in the tank that are wired in series the pressure switch you can buy at napa auto parts op6616 or ps126
51 61 do not wait for the mfin and basically stay where you put them until you reset 21 wairts for the m fin you would wire a switch to the m fin and when you close the switch the machine will open...
when you lift up on the handle of the pump it manually cycles it and normally on most machines it should pump about 3 ccs of oil into the system this can be measured by disconnecting the line coming...
the spindles are balanced and the drawbar is part of the assembly never had anyone remove the drawbar from a 12k spindle good luck.
you need to take the 9 pin connector that goes to the screen coming from the control panel not the cable from the monitor and cut it open or unscrew the case and you need to solder or splice the...
the pass fail is really only for hydraulic pumps on lathes and tsc pumps on larger mills they are the only 3 phase motors that need to be phased.
i have set up a midaco 4 pallet system 2 on either side of the machine it depends what io board you have to know what the input addresses are the inputs for the pallets are already there. there are...
on the left side of the io board most of the small connectors are inputs what you have is a sinking logic, basically you have to take a ground wire and short it to one of the inputs and you should...
it can also be the brake board for the z axis brake the z brake may be losing power and clamping casing alarms the brake board is easily repairable with new diodes otherwise pay the man.
first you need to know if you have a vector drive and brushless servos or dc servos for the axis, dc machines run at 160 and vector drives run at 320. either way you need to measure the voltage to...
thanks to cnczone for giving small companies like mine a web presence.:rainfro:
wow the pmon board is old there should be a pot that is labelled a-d usually on the servo dist board machines. with a pmon not sure where it is usually you can adjust the pot you can see the feedback...
hello
does anyone have a service manual for a bridgeport mill head? i need to know how to set the gear shift lever, i had the varispeed belt and the timing belt off and the main bull gear moves up...
i am pretty sure that you should have gotten a 93-1062 for your video board it is for use with 4 series software but i cannot imagine that that will resolve you crc error. i would put the old video...
you need to do the c axis grid offset and the gear mesh contact load first then go from there.
how did you figure that one out?
there was a vintage of vector drives that had 123 alarms because they sensed ground faults in the power line usually this only happens on ungrounded systems like delta which is usually 240 volts with...
just wondering if there are many people out there that have experienced this type of noise usually a solenoid like pre charge or pocket down on smtc but it can be any solenoid. the hfo usually comes...
if one of the fans on the vector drive is dead replace it haas sells a vector drive fan kit or you can source them at newarkinone.com overheating causes 123 alarms
haas does not sell brushes anymore they sell motors. you may find an hfo that still has some brushes that they are willing to sell. the other option is see who the manufacturer is ie bison or bodine...
setting 7 off push alarm type debug fo to posit page and page up to pos raw dat in the middle of the screen not labelled turn the spindle you will see the number change
QUALITY CNC MACHINE TOOL REPAIR
20 YEARS ELECTRO-MECHANICAL EXPERIENCE
ALL MAKES AND MODELS SERVICED
HAAS MORI HITACHI SNK MATSUURA MILLTRONICS FRYER FADAL etc.
KNOWLEDGEABLE, EFFICIENT, AND...
i don't know about pennies but if you look at the processor you will see a bunch of open solder joints for memory usually on the top left of the board you will notice the bank of chips they are all...