I would 1st check the Y axis ways to be sure it is getting oil then I would suspect the Y motor.
Type: Posts; User: RMARCH
I would 1st check the Y axis ways to be sure it is getting oil then I would suspect the Y motor.
Here is the TNC151 service manual
The tool changer parameter number should be MP126, mine is set around 68mm
If the machine hasn't been used for a while i found the limit switches get sticky or stuck
Hi Andy,
Do you have the technical manual for the TNC 2500 ? If not here it is. You may find it helpful.
https://archive.org/details/Heidenhain_TNC-2500_Technical_Manual/page/n9/mode/2up
Hi,
I have the board numbers for the LE2500 if that helps? I have some other boards stored away so when i get a chance i will check them out maybe i have the LE2500B492274492274492276
You may find it here.
https://www.cnczone.com/forums/bridgeport-hardinge-mills/63484-bridgeport-heidenhain-parameter-lists.html
On your teksoft disk there should be a folder called UPG, The Teksoft post generator/editor is in there. UGP may already be on your computer in your Procad folder.
I run my Teksoft Procam 2000 with windows 10 64 bit with no problems.
Hi , Here is a Text File of the Parameters from my HH2500 Be Careful because yours may be different. You can Upload them to your control. Good Luck
Make sure your machine is getting enough lube.
If you got a new spindle orientation card you will need to adjust it so it will work correctly.
Now that i think about it more there is a screw you have to remove in one of the holes...Remove it and loosen the nut.
You do Not have to remove the spindle. Look at the knurled nut that you put your hand on to remove the tools, there are a few holes in it look for ( i think it's brass if i can remember correctly ) a...
Hi , I know this post is very old but i have choke # 1553883.
I was told it was new when i bought it years ago but i can't say for sure.
Thanks
Hi All ,
I was using the machine yesterday and everything was fine but when i started it up this morning the Z axis will not home. The head moves up and then feeds down slowly with out Homing.
I...
The SEM motor on the Z axis should be a MT30M4-24. I don't believe other motors will work.
Hi , I solved the problem by changing the spindle orientation encoder and the spindle orientation drive card. I changed them both because i wanted to get it fixed ASAP. I also got a new belt because...
I just found this Heidenhain 151 service manual on the web so i thought i would share it here.
[QUOTE=Handi-andi;2332974]That’s excellent thanks. Don’t suppose you have information about adding a fourth axis?
Thanks
Andrew
Hi Andy , So Sorry I do not have information about adding the...
I found this going through some of my paper work and thought it would come in useful to someone.
It is instructions for tuning axis drive boards X, Y and Z.
I hope it helps !!
I Decided to take the Sem motor apart to be sure and there is NO Brake.
Good Morning ,
I am in the process of replacing the SEM motors ( MT30M4-24 ) on my Bridgeport 412 machines and i found a company that have replacement motors but they asked me if the motor has a...
Here are a couple different parameter lists , one has more lines than the other.
I am not sure which one your machine had. Good Luck !!
You may have a TNC151 because that parameter list starts with zero
I have 2 Bridgeport interact 412's and the parameters both start with MP10 ..... I checked my 3 different parameter lists i have and they all start with MP10
Maybe this Tech Manual will help. It's for TNC2500B control
If you look at the auction page pictures it has a picture you can steal for future reference of the pull studs.
https://www.ebay.com/itm/US-Stock-2x-BT40-45-Degree-M16-Pull-Stud-Retention-Knob-CNC-Milling-Tool-Holder/372069601043?epid=2292737533&hash=item56a1138f13:g:6G4AAOSwDkpbIfHW
I would try switching the Z axis drive board with one of the others and see if the problem stays on the Z