hdpe can be cut easy on table saw
so cut it to 40-45 wide then cut 3-3.5 thick strips
cutting these """washers""" , i would make a jig with vacumholding
like 2x2 feet sized for easy...
Type: Posts; User: victorofga
hdpe can be cut easy on table saw
so cut it to 40-45 wide then cut 3-3.5 thick strips
cutting these """washers""" , i would make a jig with vacumholding
like 2x2 feet sized for easy...
for my personality , for me was simpler to start my own journey
its not looking easy, but saves on headaches
for a machinist either way need a job with large series, or extremely complicated...
long time not visiting the zone
but after 4 years still the link working
im using the clone ncstudio and it still works great
after 13 years still havent had crashing ncstudio
for this small size chinese has a type of machine
cast iron table and gantry
moving table
you can order with 6 pole motor and rpm will be around 3000-12000
price is not 2000 , but ...
i posting here , because it can be confusing
and possible others will run in thi spost too
focal point
lens has a nominal focal distance
mine is 290 and the actual distance is some...
mightbe its a 4 pole motor
and need 800 hZ..
im only guessing it so check motor make sure its two pole
try to post more pictures
from top to see contour better
and from the two end to see crosssections
heres an obj file
i could retrieve of your picture
import into fusion in sculpt mode
then move nodes to get close to the original
holes you can subtract in solid mode
the issue with...
what vfd you using?
find first the manual online
go trough on manual and check you set possible and set it to factory default
they can be safe
long time I had a machine with sunfar vfd...
no, it is not in ncstudio
this card, the 4.5 the 5.4 or 5.6 using socalled multisegment method
check your vfd manual and you going to find a section where you set in 7 different segments...
first try to get a pendant
this is a very large sized machine to jogging and setting up from several meters distance
what is good thing, the Z axis sufficiently large if you need a...
do you have hand wheel for the machine?
I just asking because I don't see plugged in into control
you got a great machine
I know people bought from blue elephant and they like it
the program associated with the card you have in the computer
trough on pci bus is very reliable
this...
what I am sure, if I ever add 4th axis or ATC I going to use either way weihong or syntec control..
well
what you mean try to study a bit?
if you don't read the manual, then you wont figure it out..
when did you buy this machine?
what machine is it?
have you ever read the manual?
...
another reason for the arcs in tight corners machine can jerking if acceleration too high, meanwhile same corner described with arcs machine slows down..
so arcs are better option
thank you for posting
code is ok
im placing in program parts where they actually on table
it means my codes always in positive area of cordinata sytem..
try to move in the ...
the G2 G3 command shouldn't stop any control..
windows warnings are different
like yellow exclamation mark or red X in grey button
those characters are due your computer not installed ...
if you opened pdf, you can see on your control theres a toolsensor terminal
this pdf, for the ncstudio V10 describes how you can use the
in the 3.2.3 chapter describes how you can set rough...
heres a pdf for your control
http://www.weihong.com.cn/en/uploads/soft/160816/1-160Q6110323.pdf
just don't run to change because you don't get better control
heres an email I have
[email protected]
no, it is not the clone card
indeed its an expenses card
https://www.aliexpress.com/item/3-axis-weihong-cnc-control-system-PM95A-for-cnc-machine/32719370039.html
makaplan
have you got any help?
a new ncstudiocard cost around 35..
same way you can buy another breakout board for 30-50 and run mach3.. from computer
but that going to be way...
im very confused about this grounding issue
I understand the importance.. around the 60's electric stuff weren't double insulated so we grounded everything
mainly to the water pipes, they...
actually theres some programming guide a pdf by weihong
it made in 2013.. I cant find link right now
also on the disc you could find a text file describing functions trough on G...
if version is 5.5 or 5.6 or 5.4 then its clone
not much less from original
if you need exact position then just hold down some stops made out of scraps then mill them
then your part...
on ebay you can buy always xp computer
however i just purchased month before a few new part for my router, then seller told me win7 32 bit can run ncstudio
its pending on what ncstudio you have
if you have the original, then weihong helps you
if you have the clone version then your simples solution is touching the 4 side and using calculator...
the plastic spacer only temporary, i had 85 mm spindle and new one is 80 mm
old spindle was 2.2kW nominal however it require 3.7 inverter at least..
the aviation connector inside motor...
not this weekend but last worked on my larger router
installed spindle and a mini vfd..
i followed manual and it is working since 10 days..
reason i posting i also installed new...