My 12 year old1100 S3 had many under torqued wires, I went thru and tightened all the visible connections. I did have trouble with the connectors on the stepper drivers burning and discoloring,...
Type: Posts; User: popspipes
My 12 year old1100 S3 had many under torqued wires, I went thru and tightened all the visible connections. I did have trouble with the connectors on the stepper drivers burning and discoloring,...
I figured it out, there is a check box for it.
When drawing a circle or rectangle, is there a command to turn off points when the circle is highlighted the points automatically appear, is there a command to disable that?
Rhino 4 doesnt do...
Update: I did buy a new Dell computer,32 gig ram 8 gig video card, Win 11 and Rhino 8 runs fine on it, albeit its a bit more than what I need!
My hats off to you John!
30 holes and never threadmilled before, cutter stil in one piece, small hole to boot. I figured you would have broken at least one tool in the process!
I have never threadmilled anything, but the rpm sounds a bit high for steel?? 3500 may be better to start.
it did download it, spanish and evaluation version, I deleted it. I installed my rhino cd on another laptop with win7 and it worked fine so I would think the cd is ok, its going to take some more...
I downloaded it, took about 30 seconds, works but its in spanish! That proves it will download, its just not working from the cd.
It is free to use an educational copy until you upgrade then you...
My neighbor came over and he couldnt get it to work either, he is a programmer for Ameren. I am beginning to think it may be hardware related as I bought 2 of these Dell computers one I put one in...
It gives me a cyclic error as I try to install it even after using win 7 compatibility mode.
I ran it for years on win 7, the new version 7 takes forever to load and needs a better computer so I...
I am trying to install Rhino 4 on windows 10, I have tried the compatibility mode and no luck with that, it throws a cyclic error about halfway thru the install,. I just wonder if this can be done or...
This is the link to Mesa electronics for the board in question, 5I25T picture
This is the interface boards in question, the T means a low profile adapter, according to the description it has the...
Some grades of aluminum are not suitable for machining, they do exactly what you are describing. I use 6061 t6 mainly, other grades are suitable but are more expensive.
It is fun to play with, I have made 4 sprockets #25 chain so far for my turntable (welding rotator), the only thing I had to modify slightly was the .125 endmill diameter to .121 to get a bit more...
llink: https://sprocketeer.software.informer.com/2.0/
I found an interesting program on the internet called Sprocketeer, I needed a couple of #25 - 30 tooth sprockets for my welding turntable, I looked on the net and found this program, very simple and...
Pasturizing milk at the dairy, we heated it and ran it thru a holding tube at 160 plus degrees, it held the 160+ for a period of a few seconds then cooled it back down immediately thru the press (a...
I have been thinking about cutting about 3 keyways in my r8 collet so that it could be rotated120 degrees and have 3 locations so as to get the best runout position, mine has about a .0004 difference...
I really dont dispose of my oil coolant just add to it as it gets low, no evaporation to speak of but I do throw some away in swarf.
I use old engine oil to get the fire going in the burn barrel...
I am a kind of unorthadox guy, always trying something new etc. sometimes it works and sometimes it doesnt ha. one thing I did was to split the pdb nut and cross drill the split side for a screw to...
I think its more what one gets used too, I have used this concoction for over 50 years now and I am just comfortable with it.
I have mainly worked in stainless steel (dairy industry) and used ridgid cutting oil in the lathe and saw at the dairy, here in the shop which isnt temperature controlled I use a #2 diesel and oil...
I think maybe one reason I dont have the problem is that I leave the computer powered up all the time, it only goes down on power outage or if I am going to be gone for a period of time. I do use the...
Sounds like it may be the computer, I have had my 1100 s3 for over 11 years and no problems with pathpilot booting up. It had the large tower computer though, I changed it to a Dell 7010 which is a...
According to the (write up??), he had been ill and is now catching back up on the depleted stock. I like that they have free or reasonable shipping and made in USA...
https://www.carbidetoolsource.com
Good quality cutters, made in the US, 12 dollar shipping to Canada
edit: Copy and paste, it wouldnt let me post the whole link address.
Mine is from early 2017, MP3 it works perfect, the only thing that is a detriment lis the physical size but I am used to it now.
I found this on facebook:
https://www.facebook.com/steve.seebold
I knew Steve from the model boating forums, he ownded a Tormach and made top quality hardware for RC boats and cars.
Rest in...
there are listings on ebay for them
https://www.ebay.com/sch/i.html?_from=R40&_trksid=p2380057.m570.l1313&_nkw=tts+3%2F4+shank+collet+chucks+er16&_sacat=0
The MP 3 has an inductive output that can be removed, then it is basically a switch. l removed the inductive mecanism and added a microphone connectorll and a coiled cord that connects to the MI 8...