I do have some ER16 chucks with straight shank. Still lose almost 1" of Z from the collet nut sticking out but considering the small parts that probably will be ok for most jobs.
Type: Posts; User: GITRDUN
I do have some ER16 chucks with straight shank. Still lose almost 1" of Z from the collet nut sticking out but considering the small parts that probably will be ok for most jobs.
'95 model E2 25J.
Are there any canned cycles on these controls? Specifically for turning/boring and peck drilling. My manual does not list any canned cycles but surely there are a few that can...
Recently purchased a '95 Citizen E 25J . I had never operated a swiss lathe before so bear that in mind. Have it running fine and dandy.
However i am curious what most people are using to chuck...
Recently purchased a '95 E25J. Never worked on a swiss lathe before but have experience with the old 6 spindle cam driven screw machines and couple decades of experience operating / programming CNC...
Anyone know if an old brushed motor bar feeder will work on a newer control with the maincon? Haas techs tell me only brushless motor bar feeders made somewhere after '08 will work on newer control...
I modeled the origional and with a little fancy programming we made one from some 4140 and put it all back together. Got back up and running in short order. Still running fine.
Anyone know where i can buy this gear? Part # 20-9125A is what i was told the part # is by Haas.
I need to get a new drive gear for the spindle motor on an old '98 HS-1 20hp machine. Called Haas...
I limited the max feed to 5,000. in the post processor and it ran the code fine. Did have to open up the in position limit for the 4th axis to prevent it from stuttering during small moves but it...
What is the max feedrate you use with G93 if you happen to know off hand?
Sorry to tell you this but i have seen that screen many times. It is almost always the processor board causing that. I have a pile of processor boards in my parts room that have been replaced after...
I am trying to run a '98 model VF with an HRT-210 4th axis in G93 mode. Runs fine for a bit but will freeze after maybe 5 seconds of running. No alarm, the control just hangs. It will reset and start...
Just one last update to this nightmare that is now long over. Our problem seemed to disapear for a short period and then came back again in spades. As an absolute last resort we put isolation...
Also i have had issues a time or two in the past with not being able to enter my options codes to unlock rigid tapping, macros, etc. after reinitializing. You can call Haas and they can help get all...
I just had to reinitialize one of mine again and remembered your post. Here is some of the info i have gathered from the net and other sources. Take this at your own risk, ive used it a few times but...
Thats crap, no phone support because of liability. Id call the main offices or something. I have always had excellent phone support from Nymat.
I have reinitialized a few of mine. Not enough...
Probably need a new Mocon and yes the 102 pops up any time the servos are off such as in alarm state. Funny thing is i had one that threw up the same alarm, then i switched the mocon board with an...
Just an FYI. On most of the Haas machines i have worked on there is a parameter that can be turned on or off that monitors the voltage in the vector drive unit. This is where the computer gets its...
Ok, i changed the #5061's to #5021 and the #5062's to #5022. It works fine now and seems no less accurate. Problem solved.
I am using this macro program for a touch probe to set work coordinates for a bore hole and it works great except one quirk that i cant figure out. Macro programming is new to me so i need a little...
Ok. Got a cheap skip signal probe for $200 on Fleabay. Wired it in and ran the probe program and whoala it worked great. The probe isnt exactly the quality of my CMM machine per say but for probing...
My machines are dual pallet HS-1RP models so the macro option is already installed. The program that controls the pallet indexing is a macro program. So that would have been the biggest hurdle. I did...
Found it. Looked in one of our manuals that came with a machine.
I cant seem to find a list of the macros for Haas. I looked in the online operators manual for a mill. Maybe im just overlooking it as usual. Can someone please point me to a list or tell me where to...
Is there a touch probe system out there for older machines? I have '97 and '98 model year mills i would like to add a touch probe to for setting work offsets. Then theres the problem of macros for...
Recently purchased a late '90's model lathe with an after market USB port added on. I can send and receive files to and from the port just fine but when i put the flash drive on a PC i cant see the...
Look through the parameters in your book. I would bet however that it is a setting that can be turned off in the "SETTINGS" page. That could be catastrophic in some cases so not being able to turn...
If yours has two RS-232 ports then try swapping the cables inside the machine from one port to the other and plug your patch cord into the other port. I had the board on one of those ports go bad...
PS.
Be careful of the power wires feeding the servo amps. There is a capacitor in line that will retain power on those wires for a few minutes after the power is turned off or disconnected.
If its an older machine with brushed motors i would definately check the brushes. If brushless its either the servo amp, or the low volt power supply most likely.
Switch your X servo amp with the Y...
No. When i tried coolant it thermal shocked the inserts and tool life fell off rapidly.