Search:

I got 2 seats of mill and 1 wire and training cds for 425.00

looks good but that typically is considered x axis

You need to select the layer of the drawing it will be on the main screen by your drawing. Most likely layer 0 or 1.

Download the manual and under Tutorials follow the Jet cutting tutorial step by step,
It will answer 99.9% of the questions you will ask. If you follow that you will be good to go.

The job has no active operations = no operation selected. Sheet cam does not know what you want to do. Go back and look that you have a tool defined then on your operations window on the left side of...

Sounds like you have not specified a tool yet example= jet cutting tool.
do that and you should be well on your way to having more questions.
just post them here and wait for answers.(group)

At the bottom of the screen are 2 check boxes mirror X and mirror Y.
Also you can rotate the part with the A deg box.

There is a post on the sheet-cam website that addresses this. I had to edit the post to get rid of this warning, or you can ignore it.

That is great care to share the post?

Has anyone used sheetcam to program their fadal vmc?
If not can it be done?

liar liar pants on fire!(chair)

still looking for this wrench?

I would be interested.
Mitsubishi FX10 wire EDM machine, Fadal 4020, 2 Bridgeport knee mills with dro. 3 surface grinders, Blanchard grinder, vertical and horizontal band saws.
Shop can be seen...

Tool moving up in holder? Mark the tool or measure the length sticking out. Run the program and measure the length or check your mark.

just checked lowes .com and it shows $99

any updates?:bat::bat::bat::bat::bat::bat:

Thanks Ger21,
I do understand, however what you have posted above is a little misleading.
"with heatsink ,it was 48C" that implies that only adding a heatsink will get you -37 degrees reduced temp...

As evidenced by Gecko's own testing there is no change in temp using a heatsink. So why add a feature that has no value?

Sorry but my plasma dose not need the vfd so I do not want to pay for the...

With a multimeter. You could plug a male db9 in and probe the pins. Also you could screenprint hash marks for various ohms like a clock face. want 3.0 ohms just line up slot on pot with that hash...

:banana:
1 vote for this suggestion!

Put a current set potentiometer that adjusts the current from 0 - 3.5A. on each motor output. That way the user could set the current easily with a small screwdriver based on which motor combination...

Not sure if you had any progress removing that broken tap, if not you can purchase a tap extractor from Mc master carr. Not sure what size you need but here is a link McMaster-Carr.
They run $9.00 -...

I just found it and it works! I had been adding them manually.Only been using it about 2 weeks.

Thanks Bubba! How far are you from lee's crossing? I lived in Lagrange for many years, moved to...

Auto tabbing would help a lot of people it is quite time consuming manualy

Wow that is perfect! thanks alot I will post after cutting and painting.

First request here not sure if this can be done.
Can someone convert this to DFX suitable for plasma?

Thanks Kelly,
That is what I was looking for.

I lean,
It looks to me like your pen holder is not holding the pin tight. If you watch the top of the holder the washers and bolt seen to move around front back side to side.
Could this be your...

Thanks Tom,
I was going to use the" small wire jumper trick" to bypass the hand torch safety
switch and make up a CPC cable to short the 2 pins. I ordered the relay and will try to figure how to...

Thanks the cutter is a Powermax 45 it states in the manual that Start (start plasma) Normally open 18 VDC open circuit voltage at START terminals. Requires dry contact closure to activate.pins 3, 4....