Search:

Have a Mori SV 500 mill that the tool takes forever to clamp. Is there a procedure available to remove the Draw bar and how to repair it?

Thanks for the help in advance.

Have a NV5000 Fanuc 18imb control that has the windows xp frontend. I want to get a SRAM backup form it. It doesn't work like the older controls without windows. Holding the 2 right side soft...

I figured it out. The top setting in PMC area was not turned on to allow input and output of pmc parameters and ladder.359540

I have backed up everything except PMC parameters via serial port. I am getting no i\o soft key to backup pmc parameters.
This does not work in other words.....

To set the communications...

I have a Fanuc 18 control that i need to backup PMC parameters on. I tried to do SRAM backup, but get a corrupted data error. I have followed the manual for backup of pmc data by turning on(keep...

I wrote a small program to loop on a Hardinge 42 with Fanuc O control. It works fine for say 45 to 60 minutes then stops in cycle without any alarms. Reset program and starts again fine till around...

I wrote a small program to loop on a Hardinge 42 with Fanuc O control. It works fine for say 45 to 60 minutes then stops in cycle without any alarms. Reset program and starts again fine till around...

Sorry, this should be in Lathes forum.

I wrote a small program to loop on a Hardinge 42 with Fanuc O control. It works fine for say 45 to 60 minutes then stops in cycle without any alarms. Reset program and starts again fine till...

That was it...used Macro B instead of Macro A. The L2 in gone now. I Thank you.
P.S. Thats what we get for transfering a program ran on a 18i control to a Ot.

I have a lathe with a Ot control that gives a ps10 alarm at this line in the program;

"G10 L2 P00 X0.0 Z (#100-#512);"

This works on all other O series controls. I am not a progammer, but know...

Well, I will use the HandyFile to back with serial port then. Just SRAM is so short and sweet..lol

I can't get a Mori with an 18i control to do a sram backup. The first 512mb file does fine. The second file gives me a sram parity error. There have been no problems with this control. Runs fine...

I tried it and they are already set to 0. This is a 0-tt control...on a Saginaw twin vertical lathe. The screen should show sv-prm for the soft button, but doesn't. Anything other than parameter...

How can I turn on the servo diag page. It is on the soft key menu with parameter and diagnostics. The one that shows the load and percent of current of the specific axis and the axis parameters. ...

It is a Mori MSC 803 control and Meldas 64 cnc. What card do I need to backup software\programs...ect. ? I have a flash card with pcmcia adapter. Won't work. Do I need ATA or SRAM card??

Problem was that older Fanuc controls (I forget the models...16, 18) have the card slot, but cannot use flash memory cards. These have to have a sram card. The PMC doesn't communicate with flash...

There was not supposed to be a module in the crt slot....it is on another option card. Someone put the PMC module in the crt slot on the main card leaving no PMC module?? Just what we were told. :)

Turns out that the pmc module was in the crt slot. DUH!! Someone must have swapped them somewhere in the troubleshooting.

Called Fanuc in for that.

I have 2 Mori MSC-501 controls that I can't get the SRAM backed up. It tells me "memory card mount error". What does this mean? I can't find a card slot inside the control cabinet?

Thanks

Update, The main board number is a16b-2200-090.
NC status leds
OFF ON OFF OFF
Alarm leds
ON ON OFF

Option board #2 has alarms also...

Status for it is:
OFF ON OFF OFF

I got the parameters backed up....
The small ram card was an a20b card. I didn't get the main board number...

I had a 910 come up first while running. After removing the main cpu board, I found some oil residue on some of the small chip cards. Cleaned them off with some contact cleaner and blew them off...

I am no expert, but Rapid backlash is for rapid moves. Backlash alone is for cutting movement, and what you will need to keep set for good parts.

If I remember right, this maxes out the soft overtravel limits so machine can jog farther in the direction of overtravel letting it home. O series control parameters for overtravel are 700 thur 702...

I got to boot screen and after selecting sram backup option, it said no card inserted. Is there an option that I have to set first?

I want to do a SRAM back of some MSC 501 control. They have the PCMCIA slot and I think a 18i control. I can't get to the boot screen the same way as other 18i controls. What or where can I find...

Are you getting any alarms after the attempt to home the z-axis?

I am not a progammer, but are you talking about a M30 (Program end, rewind)

Thanks, that helps. I am getting the company to buy me the cf card and adapter to just do sram backups soon... :)