Search:

I know this is a stretch . Looking *for*back up disk for Anilam 1100 commando control*

Thanks

Hello
Can a part spring or warp during normalizing . 17-4 ph is the steel
Thanks

Anyone have any sample employee evaluations froms. Job shop related ? We are wanting to start . Does anyone do employer evalutions alos?
Thanks

Does anyone hace some basic macros for this machine they could share? We bought this machine used and it is set up for a Renishaw Probe but we have no info other than that.
Thanks

should i oversize tap a2 steel or will it stay put. heat treats to 60 rc . the tap size is 3/8-16 and we have +.005 taps. Anyone do this on a regular basis.
Thanks

4140
42-46 Rc

When my parts come back from heat treat the small holes are always packed with gunk i believe is from the heat treat solution. Is the a good solvent for this . Its a bear to get out and there is alot...

I.m looking for some used makino mc98 hmc pallet tables . Any ideas where I could track some down? Roughly 24-3/4 sq table

found it

using mastercam x3 right now going to be upgrading to x5

117827

117828

117829

professional series 3 control by fanuc and a drum tool rack

shop just bought a used makino mc98-a99 5axis hmc . anyone have experience whith this machine. I'll be programming with mastercam.
:cheers:

I have a print call out (helix=2.074 on circumference per foot of roll length
42 teeth equally spaced) the part dia is 12 inches and the length is 24 inches. want make a program to cut this helix...

i got a large program that the controls segments in the memory then calls the segments to active memory as needed. my ? is can you run a sub routine with a segmented program. THe program being called...

we just purchased a used maxim 630 and i'm having trouble getting the pallet offsets to work. I can set a fixture offset for pallet 1 but having trouble activating the offsets for pallet two.

shop just bought this used hmc .mastercam will be used to program it. Does anyone have experience with this control and machine? Just wanted to know if there is anything to look out for. I use the...

shop just bought this used hmc .mastercam will be used to program it. Does anyone have experience with this control and machine? Just wanted to know if there is anything to look out for. I use the...

X mr2 does not seem to be picking up the different feed rates when using change at point option on a od path. i 'm using the okuma post for the osp5000 control .is this a post issue?
thanks heavy

well it from the customer saying i was going to have to eat it .then he called back and said weld it. then when i was down at the weld shop the custonmer called and said elongate it just in the nick...

thanks for the replies I will found out today what the customer is going to say.I hope the dont scrap the part. we have been real slow and it seems like more mistaked happen when you dont have any...

good morning
I have a part that is calls out to be balanced dynamically with 2oz at about 2200 rpm. this part assly. to another part that is a bigger dia. my ? is i have to elongate a couple ...

steve that did not seem to work

i'm using the okuma post for the osp 7000 updated fron ver 9 to x
when i try and post a thread op (longhand or canned) it puts the start of file info at the end. does anyone no what would cause...

no i got another problem LINE 0008 the x value is outputting zero ??????
O0001G97S239M03 lsof$ phomecall 80.
N0001G70 lsof$ phomecall 80.
N0002G90 ...

hi mike
i got part figured out. just changed to cssr= vequ (c1_xh)$

Good morning Mike
i ran a test program at the machine and the changes you showed me work except i need the r value to = the value of the home position then as the tool approaches the part the chuck...

that didi it
thanks i,m new to the lathe end of it. some stuff looks similiar but i think the control is dated and that makes for alot of post mods . i am using the mastercam psot for the acramatic...

Hi Mike
Thanks for the help it seems to recongize the change but is outputting a R0 everytime??????????

hi mike
is this the area i should make the change doing something with pfxout


pcss #Output Constant surface speed
speed = c1_ss
result = nwadrs(strr,xabs)...