Dear Sir.
Fanuc 10T PMC PARAMETER PAGE "DATA TABLE CONTROL DATA" :
I need information regarding PMC PARAMETER PAGE " DATA TABLE CONTROL DATA", I am not able to enter data on Table. NO.0.,...
Type: Posts; User: dinesh
Dear Sir.
Fanuc 10T PMC PARAMETER PAGE "DATA TABLE CONTROL DATA" :
I need information regarding PMC PARAMETER PAGE " DATA TABLE CONTROL DATA", I am not able to enter data on Table. NO.0.,...
Dear Mr.guhl,
Thanks for your reply. Hence i am not background knowledge of electronics i don't know F/v converter. please let me know how to convert it.
Thanks again.
Dear Mr. G59 And Mr. guhl,
This motor is used with 5v encoder and there is no feed back. For TSA and TSB signal come from the NC.
Any further information highly apprciated.
Thanks
Dinesh
Hi,
I would like to use Fanuc A06B-6047-H003 DC(open loop) drive for single axis just to control the speed. I tried to run the motor using battary box(pin no.7 and 20) , But motor "run away" Hence...
Thanks Mr. Fordav11
Sorry for late response. I called fanuc guy, He quoted around 3000$. He suspect mother board problem. Fanuc guy yet to come to see machine.
thanks
dinesh
Dear experts on this Zone.
We have Millstar m/c with Fanuc 18i-MB.
The problem is when we are running part program CNC stops in the middle. And CNC gets hang up. We can not operate any...
Hi,
I would like know the parameter to by pass the second feedback(scale) on Fanuc OM-C control. and need to know the any modification in connection.
thank you.
dinesh
I need procedure on Pro-3 to see the ladder and i dont want to edit ladder.
can some body help.
with regards
dinesh
I also thinking same, Makino has their own plc on this machine which they can be accessed. Regarding error message which parameter can help. i am able to get stranded cnc display in English.
Hi
We did purchase makino HM J55 with Professional 3(Fanuc 16M) controller.
I am unable to see PMC ladder and error message on display is in Japan.
I am unable diagnose any problem.
If any body...
Hi Ghul,
Please send old series fanuc servo manual like A06B-6048,A06B-6050 and spindle
my email "
[email protected]
today i had same problem is anybody has nc basic file and other back up to restore
thanks
Hi, Al,
Thank you very much again. I am able to rewire the encoder cable referring to your given manual and it is working fine.
With best wishes
Dinesh
Hi,
We brought used moriseiki machine while shifting machine had an accident and most of the cable damaged. to rewire i need fanuc 21MB hardware connection manual
especially i need Pulsecoder...
Hi,
check for G 7.2 bit(pmc to cnc signal for cycle start) And G8.0(Interlock signal) for the axis movement in the PMC ladder logic,
gudluk
Hi Al_The_Man,
Last week we purchased morseiki mf6 which has Fanuc 16MA. I am able to take backup of parameter and programs as well.Machine is running fine.
Today i wanted to check RMT...
I need Fanuc 16MA operation and maintenance manual.
My e-mail [email protected]
Thanks in advance.
If you dont mind can u list the manual which u have.
with best regards
Dinesh:)
thanks for the reply.
Yes, I tried with feed rate o.05 it moves physically 200mm/min and with any feed rate program also it moves with 200mm feed.
i will try G01 with G98 in MDI and check.
I...
Hi,
We did purchased last week a used Moriseiki cnclathe. I installed it start working nicely.
But the problem know the feed rate is not changing by the G01 X...F.. command. what ever the F.....
Hi,
Company purchased used CNC grinder with Fanuc OGC control.With out manual i could able to run the machine by using stander G code.
Can anybody help me the operating manual in any form.This...
Hello your help is needed.
Problem in initializing Bubble memory with Fanuc 11m,
Due to frequent BUS ERROR and intermittent stop of the machine while running I cleared memory by pressing 7 and...
Hi Al,:confused:
I tried 3 wire system cable already.I get time out alarm. I believe there should be different cable for old model PMC like K/L/M/P. With this 3 wire system I am able to...
Hi everybody, :confused:
I would like to know pin details or cable connection detail for communicating PC to PMC of Fanuc OM series.For this wether i should use RS232 or RS 422....
Hi,
If you don"t mind,Will you send the manual to
[email protected]
Hi Dancy
This is really nice links, do you have same type for "O" series fanuc manual.
Thanks,
With best regards
Dinesh
Hi Viorel,
I tried 60 bit# 2, but PMC is not displaying.And same bit is working with other machine on which pmc is already is displayed (tried 60#2 0/1).Is there any other option.
Thank you...
Gentle men,
I have fanuc OM-C system(M/C THK GRINDING). I am getting "Not ready" alarm.There is no manual for this.Also with DGNS page PMC ladder not displaying. I would like to know is threre any...
Thanks,
In fact i was trying this manual from fanuc,But no response from them.
Virol 26,Great job.
Regards
Dinesh
I have some manual for this machine,But this is in hard copy.If your are any thing to know specific i can help you.
We purchased used NIPPIE CNC grinder.Which is used Fanuc Powermate (A02B-0122--B003).When we switched on alarm 613 P/S Alarm is comming.In master PCB LED1 red glows and LED5 green glows.I dont have...