the larger face on the inner races will be toward the outside, the larger faces of the outer rases will be toward the inside. The type and amount of grease you put between the balls is absolutely...
Type: Posts; User: allen mullis
the larger face on the inner races will be toward the outside, the larger faces of the outer rases will be toward the inside. The type and amount of grease you put between the balls is absolutely...
Boy that seems like forever ago. I've learned a lot since I did that video!
I would point out that the bottom of the line koma 8" rotary had 3X's the torque, but the worst thing it'll do is fault the drive or crash, how bad could it be.?
so youre going to depend on the motor bearings and shaft to hold up to the pressures of machining? mmm, sounds sketchy, besides that, I hope they are big angular contact or something super rigid,...
I would also recommend getting a Yaskawa Sigma 2 drive and motor. At least with that, all the parameters are known and should be about the same as your other drives.
its easy to do, but as far as I know, they are out of production, so milltronics new old stock is the only place to get them. I've looked...
It is also possible, depending on the era of control that the chip for the 4th and 5th axis were left out of the break-out board. Beside the pots on the breakout board in the card cage, you will...
Thanks for the reply Joe, I ended up buying the cpc port upgrade from hyper therm and getting a ready made DIN to Amphenol adapter cable so everything is now plug and play. I should be able to use...
I called hypertherm yesterday, they are supposed to email me with schematics of their machine that should get me where I need to be. It really sucks that given the price of the plasma cam for what it...
So I bought the DHC2 4x4 model around 08' along with a hypertherm powermax 1000. The other day, (after 10 years ) the 1000 took a dump. I have an 85 that I used for hand work and now I have bought a...
Stick a sigma 2 yaskawa drive and motor in it. At least then if the drive fails later you can do either a sigma 2 or 5 for a replacement. You can probably find the pair for under a G on eBay.
I think I've got a few as well.
I happen to have a tool changer off a partner 1 sitting on the shelf. 2 of my partner ones had changer and the parts I run on them use one tool and are pretty big, so I yanked the changer. I did take...
That is probably the number two machine I would pick for a garage period. Yes it will run on single phase. There are so many features that make it ideal for a garage. The coolant tank is only about...
I just re read it, do CALL O#### and that's it. Too simple. You're over complicating it
Eliminate the space between the O and the program number.
Try this in line 30, call O1002 , if it's a program call
If it's a sub program, place it after the end m30, make the first line begin with a high line number, like 1000, and call it like this, go...
Do you have a programming manual? They are free for download on milltronics site. To answer your question, I don't really know what you did wrong, but there are a few things I don't particularly do,...
I don't really think you need to warm up the table, but to each their own.
Go Sub 100 L30
M30
N100
G1 G53 X0 y0 f150
G4p2
G1 G53 x-25 y-15
G4 p2
Return
When someone has a code problem, they usually post the code in question. Without being able to see what you're trying to run, it would just be a guess with respect to a solution.
One of the first things I would do on any DC machine that has been sitting for an extended period and is running away is to pull all three axis motors and clean the tach feedback commutator with a...
On my lathes I have written a little program to take them home minus 1/4", load tool 1, wait 4 seconds, and estop. On my Mills, in particular any bed Mills, I empty the spindle if a tool is in it,...
If it doesn't need to stop to shift, it would be the only one I've ever seen. Wonder what a set of contacts look like after opening and closing with 20 amps at 220 v going through them. I know that...
If it's a DC machine, why not just run it on 220 single phase? L1 & l3 to your hot legs and jumper l1 & l2. Any rotary phase converter is going to give you a wild leg, the generated leg. Turn it on...
So it would be most helpful if you would post the lines that you are trying to run do we can tell what is missing.
Without that anybody would be shooting in the dark.
I have hauled several p1 mills. Unfortunately there's not a really good way to you're them down. However, in my experience, the best way I've found is to strap from one side of the trailer around the...
You need to post this in the milltronics forum
The previous post in the Milltronics forum. Sportybob posted some information on what path.dat does. Could be helpful. It would be helpful for us to know what kind of control you have. Take the cover...
you could check the previous post in this forum to see what your path.dat "should" look like.
why don't you check your path.dat file and see if it is correct. Check in ram and rom.